Keyence LS-7000 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Sensoren Keyence LS-7000 herunter. KEYENCE LS-7000 User Manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 192
  • Inhaltsverzeichnis
  • FEHLERBEHEBUNG
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen

Inhaltsverzeichnis

Seite 1 - LS-7000 Series

User’s ManualHigh-speed, High-precision Digital MicrometerLS-7000 Series96M12219

Seite 2 - General precautions

viiiNo.Measured vaMeasured vabetween the rand thresholdsetting. (See paPress the DISPLS-7001 Operation MapPROG No.PRINTESCPROGFUNCENTFOCUS21AREAPOSITI

Seite 3 - Safety Precautions

4-48Chapter 4 Function Settings4 Strobe Output TimeTake the following steps to set the ON-time of strobe output.1 Press the ENT key when the outputs

Seite 4

4-49Chapter 4 Function Settings4 OFF-delay TimeTake the following steps to set the OFF-delay time for comparator output.1 Press the ENT key when the

Seite 5 - ■ Precautions for LED

4-50Chapter 4 Function Settings4Tolerance (LIMIT) SettingsThe LS-7000 Series judges whether or not the measured values pass the criteria. Therange of

Seite 6 - OP-31973

4-51Chapter 4 Function Settings4Limit SettingsTake the following steps to make tolerance settings in reference value mode or thresholdmode.Refer to S

Seite 7 - About this Manual

4-52Chapter 4 Function Settings41 Press the key corresponding to thetype of tolerance to be set.The corresponding tolerance itemflashes. The followin

Seite 8 - Optimum Measurement Methods

4-53Chapter 4 Function Settings4Possible Setting Conditions● Reference Value in Tolerance ModeReference value + Lower limit hold value < Reference

Seite 9 - Configuration of Manual

4-54Chapter 4 Function Settings4Option SettingsSettings, such as display unit and I/O terminal mode, are available on the LS-7000 Series.Option Setti

Seite 10 - LS-7001 Operation Map

4-55Chapter 4 Function Settings4Flow of Option setting DisplayTIMLOGOHIOUT 2OUT 1PROG No.PRINTAREA DISPLS-7000ESCPROGFUNCENTHOLDZEROFOCUS21AREAPOSITI

Seite 11 - Hold function (See page 3-5)

4-56Chapter 4 Function Settings4Tolerance Mode (LIMITS)Take the following steps to select the appropriate tolerance mode.Setting RangeThe following m

Seite 12 - Contents

4-57Chapter 4 Function Settings41 Press the ENT key when the optionsetting is displayed.2 Press the FUNC key.3 Press the or key and set thetiming

Seite 13 - Chapter 4 Function Settings

ixHINo. AREA DISPLS-7000HOLDZEROHIGOLOTIMLOGOOUT 2OUT 1Measured value display selectionMeasured value display varies between the reference value mode

Seite 14 - Appendix

4-58Chapter 4 Function Settings43 Press the or key and set thedisplay unit.The following displayed items can beselected.mmμmGOGOinchmilGOGOTo cha

Seite 15 - Chapter 1

4-59Chapter 4 Function Settings41 Press the ENT key when the optionsetting is displayed.2 Press the FUNC key three times.HIGOLO3 Press the or key

Seite 16 - ■ Principle of Measurement

4-60Chapter 4 Function Settings4Units, Default Minimum Values, and Setting Ranges0.00001mm0.01μm0.00000mm0.00μm+30.00000mm+30000.00μm0.00000mm0.00μm+

Seite 17 - System Applications

4-61Chapter 4 Function Settings40.0000005inch0.01mil0.000000inch0.000mil+3.000000inch+3000.000mil0.000000inch0.000mil+4.000000inch+4000.000mil–0.9999

Seite 18 - Package Checks

4-62Chapter 4 Function Settings4MEMO

Seite 19 - Chapter 1 Getting Started

5-1Chapter 5Environment SettingsThis section provides information on environment settings thatinclude RS-232C interface settings along with basic oper

Seite 20

5-2Chapter 5 Environment Settings5Possible Environment SettingsThe following environment settings are possible.• Program: Program setting changes, pr

Seite 21 - Functions and Nomenclature

5-3Chapter 5 Environment Settings5 Head (See page 5-10)Item Setting rangeLED inspection function (L-INSPCT)(–) HEAD1, HEAD2 (Connected head number)M

Seite 22 - ■ Control Panel

5-4Chapter 5 Environment Settings5Flow of Environment Setting DisplayTIMLOGOHIOUT 2OUT 1PROG No.PRINTAREA DISPLS-7000ESCPROGFUNCENTHOLDZEROFOCUS21ARE

Seite 23

5-5Chapter 5 Environment Settings5Details of Environment SettingsThis section provides information on environment setting items and setting methods.P

Seite 24

xContentsSafety Precautions ...iPrecautions

Seite 25 - Mounting and Connection

5-6Chapter 5 Environment Settings51 Press the ENT key when the program display is on the screen.2 Press the FUNC key.3 Press the or key to select

Seite 26 - 2 Mount the measuring head

5-7Chapter 5 Environment Settings5RS-232CTake the following steps to make the communication settings for the RS-232C interface andrelative settings f

Seite 27 - Mounting the Controller

5-8Chapter 5 Environment Settings53 Press the or key and select the parity.The following displayed items can be selected.NoneEvenOddGOGOGO4 Press

Seite 28 - ■ Mounting to Panel

5-9Chapter 5 Environment Settings53 Press the or key and select the data mode.The following displayed items can be selected.NonePLCPrinter 1Print

Seite 29

5-10Chapter 5 Environment Settings5HeadTa ke the following steps to set the LED inspection function and mutual interference preven-tion function.Sett

Seite 30

5-11Chapter 5 Environment Settings5Check on Fluctuation of Light Intensity Due to Dirt or DustTo check the dispersion of the amount of light, record

Seite 31 - Connection

5-12Chapter 5 Environment Settings5 Mutual Interference Prevention FunctionThis function prevents mutual interference that may result when two measu

Seite 32 - ■ Power Supply Cable

5-13Chapter 5 Environment Settings5Panel LockTake the following steps to specify the panel lock range when the panel lock function is set.Setting Ran

Seite 33 - Measurement and

5-14Chapter 5 Environment Settings5MEMO

Seite 34

6-1Chapter 6I/O TerminalsThis section provides information on I/O terminal specificationsand timing charts.Nomenclature and Functions of I/O Terminals

Seite 35

xiChapter 4 Function SettingsFlow of Program Settings ...

Seite 36

6-2Chapter 6 I/O Terminals6Nomenclature and Functions of I/O TerminalsThis section provides nomenclature and functions of the I/O terminals of the LS

Seite 37 - Chapter 2

6-3Chapter 6 I/O Terminals6I/O Signal Names and DescriptionsThe I/O terminals handle the following signals. Refer to Function on page 6-7 for thefunct

Seite 38 - Set value

6-4Chapter 6 I/O Terminals6Connector I/OConnector I/O signals operate in either SUB mode or BCD. Refer to I/O Mode on page 4-59 for details.Applicabl

Seite 39

6-5Chapter 6 I/O Terminals6SUB ModeTerminal numberCable colorSignal name Description123456789101112131415161718192021222324252627282930313233343536373

Seite 40

6-6Chapter 6 I/O Terminals6BCD ModeTerminal numberCable colorSignal name Description12345678910111213141516171819202122232425262728293031323334353637

Seite 41

6-7Chapter 6 I/O Terminals6FunctionsThe following section provides information on I/O signal functions. For the arrangement ofeach terminal, refer to

Seite 42

6-8Chapter 6 I/O Terminals6The following table shows a list of program numbers and the status of the P1 terminalthrough the P4 terminal.Program numbe

Seite 43

6-9Chapter 6 I/O Terminals6 BCD OutputName Description Reference page6-66-66-66-66-6BCD POLE output BCD polarity output.OFF: PositiveON: NegativeBCD

Seite 44 - Measurement of Pitch

6-10Chapter 6 I/O Terminals6 NPN Open Collector Output 2Output+5V+5V470Ω10kΩ10nF10kΩCOM2Internal circuitMax. applied voltageMax. sink currentResidua

Seite 45 - Chapter 3

6-11Chapter 6 I/O Terminals6Timing ChartThis section provides information on the timing charts of BCD output in a variety of meas-uring modes. Normal

Seite 46 - Chapter 3 Operation Control

xiiChapter 6 I/O TerminalsNomenclature and Functions of I/O Terminals ... 6-2Ter minal Block

Seite 47 - Chapter 3 Operation Control

6-12Chapter 6 I/O Terminals6 Sample Hold 2ONOFFTIMING inputONOFFRESET/ZERO inputONOFFP1 input to P4 inputONOFFComparator outputONOFFWAITING outputON

Seite 48 - Area Monitor

6-13Chapter 6 I/O Terminals6 BCD Output Switching0±0.1msONOFFBCD SELECT inputONOFFBCD DATA outputONOFFBCD INDICATE outputOUT1 Measured valueON

Seite 49 - Hold Function

6-14Chapter 6 I/O Terminals6 Minimum Input PeriodRefer to the relevant timing charts for the delay time (response delay time) in responseto input.N

Seite 50 - Automatic Zero Function

7-1Chapter 7RS-232CThis section provides information on how to connect the LS-7000 Series to external devices along with RS-232Ccommunications functio

Seite 51 - Panel Lock Function

7-2Chapter 7 RS-232C7SpecificationsThe LS-7000 Series has RS-232C communications functions. The following section pro-vides information on the RS-232

Seite 52 - Program Changes

7-3Chapter 7 RS-232C7 RS-232C Connection SettingsMake the following environment settings according to the connecting device. For details,go to the r

Seite 53 - Chapter 4

7-4Chapter 7 RS-232C7Communication using Serial CommandsTo enable the LS-7000 Series to transmit measured values or allow setting changes,connect a p

Seite 54 - Flow of Program Settings

7-5Chapter 7 RS-232C7Connecting to KV SeriesThe following information provides information on how to connect Keyence’s KV-seriesProgrammable Logic Co

Seite 55 - Option Settings

7-6Chapter 7 RS-232C7Outline of Command FormatsWhen LS-7000 Series receives a command from the external device, the LS-7000 Serieswill respond to the

Seite 56

7-7Chapter 7 RS-232C7Measurement Serial CommandsThe following section provides information on serial commands used for measurementcontrol.List of Com

Seite 57

1-1Chapter 1Getting StartedThis section provides information on the configuration of theLS-7000 Series, precautions, and necessary preparationsrequire

Seite 58 - ■ Program Initialization

7-8Chapter 7 RS-232C7Commands in DetailThe following section provides information on commands and responses that the LS-7000Series returns when comma

Seite 59

7-9Chapter 7 RS-232C7Peak Hold, Bottom Hold, Peak-to-peak Hold, Average Hold, or Sample Hold 1Measuring modeU [ ] L [ ] U [ ] L [ ]U [ ]Measured valu

Seite 60 - (See page 4-14)

7-10Chapter 7 RS-232C7 Timing ONThis command turns timing input ON.With command H0 executed, the operationof the LS-7000 Series will be the same ast

Seite 61 - Area Selection

7-11Chapter 7 RS-232C7 Program Number SelectionThis command selects program numbers.The command will be enabled if PANEL isset as a P-SELECT environ

Seite 62 - ■ SEG (Segment)

7-12Chapter 7 RS-232C7Setup Serial CommandsThe following section provides information on command formats that are used to makesetting changes.List of

Seite 63

7-13Chapter 7 RS-232C7 Numeric Setting Format (m m m m m m m m Format)This format is a fixed length format consisting of a single mark character and

Seite 64 - ■ Setting Procedure

7-14Chapter 7 RS-232C7 Area CheckThis command makes area check ON/OFF settings and changes the number of edges.LSNumber of area check edgesOFF : OFF

Seite 65 - SEG (Segment)

7-15Chapter 7 RS-232C7 Measuring ModeThis command changes measuring mode settings.LSOutput number1 : OUT12 : OUT2Measuring mode00 : NORMAL 04 : AV-H

Seite 66

7-16Chapter 7 RS-232C7Threshold ModeLSOutput number1 : OUT12 : OUT2CommandResponseS D,A O,h m m m m m m m m,m m m m m m m m cr,S D,A O,h cr+10V set v

Seite 67

7-17Chapter 7 RS-232C7● Threshold ModeHHLSOutput number1 : OUT12 : OUT2CommandResponseToleranceValue setting format (See page 7-13)S D,H H,h m m m m

Seite 68

1-21Chapter 1 Getting StartedOutline and Features of LS-7000 SeriesThe LS-7000 Series is a high-speed, high-accuracy digital micrometer used for the

Seite 69 - 6 Press the

7-18Chapter 7 RS-232C7 Hold Value Elimination ON/OFFThis command turns the function of abnormal value elimination ON and OFF.LSOutput number1 : OUT1

Seite 70

7-19Chapter 7 RS-232C7Serial Commands to check the LS SettingsThe following section provides information on command formats used to check settingdeta

Seite 71

7-20Chapter 7 RS-232C7Batch CommandsIt is possible to read the whole setting data of the LS-7000 Series and save the data on thePC. The saved data on

Seite 72 - Calibration Settings

7-21Chapter 7 RS-232C7 Reading Environment SettingsIt is possible to read all environment settings in detail.Note: P-COPY, P-CLEAR, or L-INSPCT sett

Seite 73

7-22Chapter 7 RS-232C7ASCII TableRightmost 4 bitsLeftmost 4 bits01234567NULDLESP0 Pp0SOHDC11AQaq1STXDC22BRbr2ETXDC33CScs3EOTDC44DTdt4ENQNAK5EUeu5ACKS

Seite 74

7-23Chapter 7 RS-232C7Communication using an External Synchronous TriggerThe following section provides information on how to obtain output from the

Seite 75

7-24Chapter 7 RS-232C7Timing ChartThe following timing chart applies to timing input and RS-232C data output (the meas-uring mode is not set to sampl

Seite 76

8-1Chapter 8SpecificationsThis section provides the specifications, characteristics, andexternal dimensions of the LS-7000 Series.Specifications ...

Seite 77 - 5 Press the

8-2Chapter 8 Specifications8SpecificationsControllerDisplay typeMinimum display unitDisplay rangeMeasuring position monitorTolerance comparator outpu

Seite 78

8-3Chapter 8 Specifications8Measuring HeadModelMeasuring rangeMinimum detectable objectT-to-R distanceLight sourceCCD scanning rangeMeasurement positi

Seite 79

1-31Chapter 1 Getting StartedSystem ApplicationsThe LS-7000 Series has a wide range of applications when used in combination withcommercially availab

Seite 80

8-4Chapter 8 Specifications8CharacteristicsMeasurement Range and Accuracy8140(30) 30±52446ReceiverTransmitterUnit: mm±1.5μm±0.5μmReceiver8035.5Transm

Seite 81

8-5Chapter 8 Specifications81505640652030100±50±6μm±3μmReceiver TransmitterUnit: mmTemperature CharacteristicsThe following table shows typical exampl

Seite 82

8-6Chapter 8 Specifications8Response Deley Time Measurement Response TimeThe following table lists the response time between the moment the dimensio

Seite 83

8-7Chapter 8 Specifications8Mode Specifications Measuring ModeStatusMeasured value display OutputRS-232CNumeric displayComparator LED5-level discrimi

Seite 84

8-8Chapter 8 Specifications8External DimensionsIt is possible to download CAD data on the external dimensions of the LS-7000 Series fromKEYENCE’s URL

Seite 85 - Measuring mode

8-9Chapter 8 Specifications8 LS-7030 Measuring Head151522±0.2 Measuring position222238266113 113 383855556026613513526660126.51095021450160 272716517

Seite 86

8-108 LS-S11 AC Power Supply Stand)(100148178171216 2016043.519614)(35 Extension CableLS-C**A Extension Cable (Cable between the controller and meas

Seite 87

9-1Chapter 9TroubleshootingThis section provides information on troubleshooting and thecontents of error messages.Troubleshooting Guide ...

Seite 88

9-2Chapter 9 Troubleshooting9Troubleshooting GuideIf the LS-7000 Series fails to operate, follow the inspection steps provided below. If the LS-7000

Seite 89

9-3Chapter 9 Troubleshooting9Problem Inspection RemedyCheck that the LED light source of the transmitter is lit.Check the connection of the cable bet

Seite 90

1-41Chapter 1 Getting StartedPackage ChecksCheck that nothing is missing from the LS-7000 Series package before use.LS-7001`96M1613LS-7010Allen-head

Seite 91

9-4Chapter 9 Troubleshooting9Check that the cover glass of the transmitter or receiver is free of dust and dirt.Remove the dirt and dust from the cov

Seite 92

9-5Chapter 9 Troubleshooting9Problem Inspection RemedyCheck that the communications cable is correctly connected.Connect the communications cable cor

Seite 93

9-6Chapter 9 Troubleshooting9Error MessagesThe following section explains error messages that will be displayed if the LS-7000 Serieshas errors while

Seite 94

Appendix-1AppendixThis section provides information on optional accessories andthe index of this manual.List of Optional Accessories ...

Seite 95

Appendix-2AppendixAppendixList of Optional AccessoriesItem AppearanceTR Cable(1m)ExplanationRS-232C Cable (for KV)TypeTR Cable(3m)I/O Cable (3m)RS-232

Seite 96 - Analog Output Settings

Appendix-3AppendixAppendixSetting Record SheetUse the following tables to record your setting details. Area SettingsMeasuring head selection (HEAD No

Seite 97

Appendix-4AppendixAppendix Output SettingsArea calculation (CALC)OUT1 : A1 1.0A2 OFFOUT2 : A1 OFFA2 1.0Number of averaging times (AVE)512Measuring mo

Seite 98 - ■ Analog update mode

Appendix-5AppendixAppendixEnvironment Setting Record SheetUse the following tables to record your environment setting details. ProgramItem Setting de

Seite 99 - Comparator Output Setting

Appendix-6AppendixAppendixIndex1One-point calibration ... 4-262Two-point calibration ... 4-2555-leve

Seite 100 - (Normally closed)

Appendix-7AppendixAppendixHHH ... 7-17HH set value... 4-50H

Seite 101 - 4 Press the

1-51Chapter 1 Getting StartedLS-7070Measuring HeadLS-C✱✱AExtension Cable (Cable between the controller and measuring head)LS-C3A: 3-m cable✱✱... LS-C

Seite 102 - Tolerance (LIMIT) Settings

Appendix-8AppendixAppendixSSample hold 1 ... 4-33, 4-38, 6-11, 7-9Sample hold 2 ... 4-33, 4-39, 6-12, 7-9Scaling ...

Seite 103 - Limit Settings

WARRANTIES AND DISCLAIMERS(1) KEYENCE warrants the Products to be free of defects in materials and workmanship for a period of one (1) year from the d

Seite 104 - Hold Value Elimination

Copyright (c) 2012 KEYENCE CORPORATION. All rights reserved.12218E 1092-1 96M12219 Printed in Japan

Seite 105 - 1 Continue pressing the

PrefaceThis instruction manual provides necessary information on the operation and maintenanceof the LS-7000 Series along with precautions. Please rea

Seite 106

1-61Chapter 1 Getting StartedLS-S11Stand Unit Base Unit Screws (Four, M4 x 8)❈ Keyence ships each package with utmost care and attenti

Seite 107 - Chapter 4 Function Settings

1-71Chapter 1 Getting StartedFunctions and NomenclatureThe following section provides information on the functions and nomenclature of thecontroller

Seite 108 - 3 Press the

1-81Chapter 1 Getting Started Control PanelTIMLOGOHIOUT 2OUT 1PROG No.PRINTAREA DISPLS-7000ESCPROGFUNCENTHOLDZEROFOCUS21AREAPOSITIONHIGOLO(1)(3)(4)(

Seite 109 - Display Unit

1-91Chapter 1 Getting Started(14) Display selection key: Press this key to select the main display or subdisplay when measuring. (Page 3-2, Switching

Seite 110

1-101Chapter 1 Getting StartedLS-7030Multi-purpose Mounting HolesA fixture for targets can be attached.Transmitter (T Head)Emits light for measuremen

Seite 111 - I/O Mode

1-111Chapter 1 Getting Started Mounting and ConnectionMount the measuring head and the controller, and connect them with the cables. Mounting the Me

Seite 112

1-121Chapter 1 Getting Started With TR BaseThe transmitter and receiver are mounted to the TR base at the time of shipment. Thissection provides how

Seite 113

1-131Chapter 1 Getting StartedCAUTIONUse the 5-mm-deep M4 bottom mountingholes of the transmitter and receiver asshown in the illustration.Mounting t

Seite 114

1-141Chapter 1 Getting StartedMounting holesMounting holes Mounting to PanelThe controller can be mounted to control panels with the mounting bracke

Seite 115 - Chapter 5

1-151Chapter 1 Getting StartedGasketSecure these potions with screws.The stand must be located on the groove from which the gasket was removed.4 Secu

Seite 116 - Possible Environment Settings

Safety Precautions General precautions• At startup and during operation, be sure to monitor the functions and performance ofthe LS-7000 Series.•Take

Seite 117

1-161Chapter 1 Getting StartedCable between controller and measuring head3 Connect the cable between the con-troller and measuring head.If only a sin

Seite 118 - This part changes

1-171Chapter 1 Getting StartedCAUTIONThe back of the AC power supplystand has legs. Erect the legs anduse the AC power supply stand ifrequired.TipsCo

Seite 119

1-181Chapter 1 Getting StartedReceiver sideTransmitter sideController sideMeasuring head side Transmitter and ReceiverConnect the cables of the tran

Seite 120 - ■ Resetting All Programs

1-191Chapter 1 Getting StartedSupply Stand On and OffThis section provides information on how to turn the AC power supply stand on and off. Turning

Seite 121 - ■ Parity

1-201Chapter 1 Getting StartedSetting OverviewThe LS-7000 Series is in measurement operation according to a variety of settings. Thefollowing section

Seite 122 - ■ Data Mode

1-211Chapter 1 Getting StartedAREA DISPHOLDZEROTIMLOGOHIOUT 2OUT 1ESCPROGFOCUS21AREAPOSITIONHIGOLOHIGH-ACCURACY CCD MICROMETERPRINTESCPROGFUNCENTRese

Seite 123 - ■ Data Transmission Mode

1-221Chapter 1 Getting StartedMEMO

Seite 124

2-1Chapter 2Easy Setting GuideThe LS-7000 Series is used for a variety of measurementapplications if the LS-7000 Series is set properly. This sectionp

Seite 125

2-22Chapter 2 Easy Setting GuideMeasurement of Outer Diameter and Width (with Single Measuring Head)In the following example, a single measuring head

Seite 126 - The buzzer turns OFF

2-32Chapter 2 Easy Setting GuideMeasurement of Outer Diameter and Width (with Two Measuring Heads)In the following example, two measuring heads are

Seite 127

Usage• Be sure to turn off the power to the LS-7000 Series and anyconnected devices before connecting or disconnecting thecables. Otherwise, the cam

Seite 128

2-42Chapter 2 Easy Setting Guide Measurement of Outer Diameter and Width (with Two Measuring Heads for Larger Objects)A sheet cannot be located in th

Seite 129 - Chapter 6

2-52Chapter 2 Easy Setting GuideMeasurement of Inner Diameter and ClearanceIn the following example, the inner diameter of the workpiece is measured

Seite 130 - Terminal block

2-62Chapter 2 Easy Setting GuideMeasurement of Outer Diameter and EccentricityIn the following example, the outer diameter and eccentricity of the ro

Seite 131 - Chapter 6 I/O Terminals

2-72Chapter 2 Easy Setting GuideMeasurement of Movement and PositioningIn the following example, the movement or position of the workpiece is measure

Seite 132

2-82Chapter 2 Easy Setting GuideMeasurement of PitchThe single pitch of connectors pins or IC pins is measured by the LS-7000 Series. Further-more, m

Seite 133

3-1Chapter 3Operation ControlThis section provides information on setting control items onthe control panel while the LS-7000 Series is in measurement

Seite 134 - Chapter 6 I/O Terminals

3-2Chapter 3 Operation Control3Selection of Measured Value DisplayDisplayed values on the main and sub displays can be switched. The main display can

Seite 135 - ZERO Input 6-3, 6-5, 6-6

3-3Chapter 3 Operation Control3 Tolerance Mode with ThresholdTIMLOGOHIOUT 2OUT 1FOCUS21AREAPOSITIONHIGOLOTIMLOGOHIOUT 2OUT 1FOCUS21AREAPOSITIONHIGOLO

Seite 136 - ■ FUNCTION Output

3-4Chapter 3 Operation Control3Area MonitorThe area monitor display can be used to confirm the insertion positions of the targets inAREA1 or AREA2 to

Seite 137 - Electrical Specifications

3-5Chapter 3 Operation Control3Hold FunctionMeasured values can be held and displayed. Furthermore, measuring mode combinationsallow the measurement o

Seite 138 - ■ Analog Voltage Output

Note: Influence of Ambient Operating TemperatureEnsure that the ambient operating temperature is constant. Achange in the ambient operating temperat

Seite 139 - Timing Chart

3-6Chapter 3 Operation Control3Automatic Zero FunctionThe automatic zero function sets measured values to zero (0.00000) instantly. This functionis c

Seite 140 - ■ Self-timing Hold

3-7Chapter 3 Operation Control3Panel Lock FunctionThe panel lock function is used to lock the control panel so that no key input will be ena-bled. As

Seite 141 - ■ BCD Output Switching

3-8Chapter 3 Operation Control3Program ChangesThe following section provides information on how to call 16 programs saved in the LS-7000 Series.Names

Seite 142 - ■ Minimum Input Period

4-1Chapter 4Function SettingsThe LS-7000 Series is available to the measurement of avariety of items by making setting changes. These settingscan be r

Seite 143 - Chapter 7

4-2Chapter 4 Function Settings4Flow of Program SettingsThe following section provides information on the types and flows of program settingsavailable

Seite 144 - Specifications

4-3Chapter 4 Function Settings4OUT1OUT2External I/OReference valueThresholdmmμminchmilSUBBCDScaling (Reference value/Threshold)Analog update modeOutp

Seite 145 - ■ RS-232C Connection Settings

4-4Chapter 4 Function Settings4Default Values and Possible Setting RangesThe following programs settings are made by default.Items in parentheses ind

Seite 146 - ■ Environment Settings

4-5Chapter 4 Function Settings4 Output Settings (OUTPUT) (Page 4-28)Item DefaultArea calculation (CALC)OUT1: A1 1.0 A2 OFFOUT2: A1 OFF A2 1.0Averagi

Seite 147 - Connecting to KV Series

4-6Chapter 4 Function Settings4Copying Program Setting Details and InitializationThe LS-7000 Series can be initialized so that the details of program

Seite 148 - Outline of Command Formats

4-7Chapter 4 Function Settings4Area SettingsArea settings are used to determine the measurements taken from a variety of objectsplaced in the beam. T

Seite 149 - Measurement Serial Commands

Precautions for CE MarkingsKeyence confirms that the LS-7000 Series meets EC directive requirements. The LS-7000Series bears CE markings. Keep the fol

Seite 150 - ■ Measured Value Output

4-8Chapter 4 Function Settings4Flow of Area Setting DisplayTIMLOGOHIOUT 2OUT 1PROG No.PRINTAREA DISPLS-7000ESCPROGFUNCENTHOLDZEROFOCUS21AREAPOSITIONH

Seite 151 - Chapter 7 RS-232C

4-9Chapter 4 Function Settings4Area SelectionAreaWhen a target is located in the measuring area as shown below, the light into thereceiver is partly

Seite 152

4-10Chapter 4 Function Settings4 T-EDGE (Top Edge)/B-EDGE (Bottom Edge)Select either of these settings for the gapmeasurement or positioning of roll

Seite 153 - Response

4-11Chapter 4 Function Settings4E (Edge) ModeThe LS-7000 Series measures objectsbased on the edges in this mode.Set the edge numbers to positive valu

Seite 154 - Setup Serial Commands

4-12Chapter 4 Function Settings4P (Pitch) ModeThe LS-7000 Series measures objectsbased on the middle point between theedges of the objects in this mo

Seite 155

4-13Chapter 4 Function Settings4screen.Measuring head No. 1Measuring head No. 2HIHIDIA (Diameter)T-EDGE (Top edge)B-EDGE (Bottom edge)SEG (Segment)HI

Seite 156 - ■ Average

4-14Chapter 4 Function Settings4The input value is entered and the value in the next line flashes.(3) Input the end edge (pitch) number.4 Press the E

Seite 157

4-15Chapter 4 Function Settings4TIMLOGOHIOUT OUTFOCUS21AREAPOSITIONHIGOLOHIGOLOPROG No.PRINTAREA DISPESCPROGFUNCENTHZFOCUS21AREAPOSITIONArea CheckSet

Seite 158

4-16Chapter 4 Function Settings4Difference CheckIf there is a radical change between measured values, the change will be detected andoutput.Setting R

Seite 159

4-17Chapter 4 Function Settings46 Press the ENT key after the value is set.The input value is entered and the area display appears again.Function Out

Seite 160

About this ManualThe following section provides information on the configuration of each page of this manualalong with symbols and terms used in this

Seite 161 - (Page 7-15)

4-18Chapter 4 Function Settings4Change of Edge Detection ThresholdThe following section provides information on how to make threshold changes for the

Seite 162 - Batch Commands

4-19Chapter 4 Function Settings4 Setting method1 Select the area to be set and pressthe ENT key.2 Press the FUNC key five times.HIGOLO3 Press the

Seite 163

4-20Chapter 4 Function Settings4Calibration SettingsThe measured value of a target may have a subtle error due to the surface condition andangle of t

Seite 164 - ASCII Table

4-21Chapter 4 Function Settings4 Procedure for Calibration SettingsMake calibration settings while monitoring the sub display.1 Press the PROG key.2

Seite 165 - ■ Output

4-22Chapter 4 Function Settings4Flow of Calibration Setting DisplayTIMLOGOHIOUT 2OUT 1PROG No.PRINTAREA DISPLS-7000ESCPROGFUNCENTHOLDZEROFOCUS21AREAP

Seite 166 - RS-232C data output

4-23Chapter 4 Function Settings4Calibration Type SelectionThe following section provides information on how to set the calibration type for each area

Seite 167 - Chapter 8

4-24Chapter 4 Function Settings41 Press the ENT key for calibrationsetting.The AREA1 calibration display appears.Press the FUNC key to make AREA2sett

Seite 168

4-25Chapter 4 Function Settings4Two-point Calibration SettingsMake two-point calibration settings as explained below.Setting RangeTwo-point calibrati

Seite 169 - Optional Accessories

4-26Chapter 4 Function Settings4One-point Calibration SettingsMake one-point calibration settings as explained below.Note: In the case of one-point c

Seite 170 - Characteristics

4-27Chapter 4 Function Settings4Initializing AREA1 Calibration Value(1) Press the or key.“Reset” appears on the screen.(2) Confirm the area to be

Seite 171 - Temperature Characteristics

Optimum Measurement MethodsRefer to the following methods, and select the optimum measurement method according tothe type of target.Measurement of Out

Seite 172 - ■ Measurement Response Time

4-28Chapter 4 Function Settings4Output SettingsValues measured in AREA1 and AREA2 can be processed in a variety of ways and outputas OUT1 and OUT2 si

Seite 173 - Mode Specifications

4-29Chapter 4 Function Settings4Flow of Output Setting DisplayTIMLOGOHIOUT 2OUT 1PROG No.PRINTAREA DISPLS-7000ESCPROGFUNCENTHOLDZEROFOCUS21AREAPOSITI

Seite 174 - External Dimensions

4-30Chapter 4 Function Settings4Area CalculationThe measured values from the two memory areas are used for calculation processing.Setting RangeSelect

Seite 175 - ■ LS-7070 Measuring Head

4-31Chapter 4 Function Settings42 Press the or key and set the coefficient for AREA1.PROG No.PRINTAREA DISPESCPROGFUNCENTHZEFOCUS21AREAPOSITIONGL

Seite 176 - ■ Extension Cable

4-32Chapter 4 Function Settings4Example: If the averaging number is eight, the LS-7000 Series will output the data asshown below.1Internal data (2,40

Seite 177 - Chapter 9

4-33Chapter 4 Function Settings4Measuring modeThe Measuring mode allows the LS-7000 Series to capture and hold measured values.Setting RangeThe LS-70

Seite 178 - Troubleshooting Guide

4-34Chapter 4 Function Settings4Application Example of Measuring modesSelect the measurement mode according to the type of target and measuring condi

Seite 179 - Chapter 9 Troubleshooting

4-35Chapter 4 Function Settings4Timing ChartThe following table lists timing charts for respective measuring modes.RUN mode Timing chart name Referen

Seite 180

4-36Chapter 4 Function Settings4 Peak Hold• Peak hold: The maximum value during the sampling period specified byexternal timing input is displayed a

Seite 181

4-37Chapter 4 Function Settings4 Auto Peak Hold• Auto peak hold: The maximum value measured by the LS-7000 Series incontinuous measurement operation

Seite 182 - 2 Continue pressing the

vii123456789Configuration of ManualChapter 1 Getting StartedProvides information on precautions and necessary preparationsrequired.Chapter 2 Easy Sett

Seite 183 - Appendix-5

4-38Chapter 4 Function Settings4 Sample Hold 1The instantaneous value at the time specified by external timing input is displayed, andthe value is o

Seite 184

4-39Chapter 4 Function Settings4 Sample Hold 2The value measured during the period specified by external timing input is displayed,and the value is

Seite 185 - Setting Record Sheet

4-40Chapter 4 Function Settings4 Self-timing HoldThe LS-7000 Series in self-timing hold operation will detect targets automatically withno external

Seite 186 - Threshold

4-41Chapter 4 Function Settings4● Self-timing Hold and Area SettingsThe LS-7000 Series in self-timing hold operation will detect a target when the ta

Seite 187

4-42Chapter 4 Function Settings4Setting Method1 Press the ENT key when the outputsetting is displayed.2 Press the FUNC key twice.3 Press the or k

Seite 188

4-43Chapter 4 Function Settings44 Press the ENT key.The input item is entered and the output setting display appears again.OffsetAn offset value is a

Seite 189

4-44Chapter 4 Function Settings4Analog Output SettingsThe LS-7000 Series has analog voltage output according to the measured value. Therange of analo

Seite 190

4-45Chapter 4 Function Settings4The following table shows the relationship of scaling values along with their outputranges and resolutions.Scaling va

Seite 191 - WARRANTIES AND DISCLAIMERS

4-46Chapter 4 Function Settings4Setting Method1 Press the ENT key when the outputsetting is displayed.2 Press the FUNC key four times.3 Press the o

Seite 192

4-47Chapter 4 Function Settings43 Press the or key and set theanalog update mode.4 Press the ENT key.The input item is entered and the outputsett

Kommentare zu diesen Handbüchern

Keine Kommentare