Keyence AP-40P Bedienungsanleitung PDF herunterladen (Seite 4)

■ Unit Setting

Determine the desired units.

In measurement mode, press for at least 3 seconds. “- - - -”

appears first, and then the current units are displayed. Use

▲

▼

to select the desired units. Pressing completes the unit

setting procedure and enters operation mode selection.

■ Operation Mode

Determine the desired operation mode.

(➮ Refer to “OPERATION MODE SELECTION” on page 3.)

The current operation mode is displayed. Use

▲

▼

to select

the operation mode. Pressing completes the operation mode

setting procedure and enters N.O./N.C. selection.

■ N.O./N.C. Selection

Select N.O. (normally open) or N.C. (normally closed).

The current selection of “no” (normally open) or “nc” (normally

closed) is displayed. Use

▲

▼

to select the desired mode.

Pressing completes the N.O./N.C. selection procedure and

enters the chattering prevention setting.

■ Chattering Prevention

Determine the desired response time.

The current response time is dis-

played. Use

▲

▼

to select the

response time. Pressing com-

pletes the setting procedure and

enters the display color selection.

■ Display Color Selection

Determine the desired LED color for

numerical value display.

The current color is displayed. Use

▲

▼

to select the color.

Pressing completes the setting

procedure and returns to the

measurement mode.

ADJUSTMENT

Measurement mode

Press the button

for 3 seconds or

more.

Press the button

once.

dtS

,gHmm:44/)M(14-PA

mc/fgk:34-PA

,aPk:44/)M(14-PA

aPM:34-PA

hcni

,gHhcni:44/)M(14-PA

:34-PAisP

RAb

rab:44/34/)M(14-PA

Press the button once.

▲

Press the button once.

5.2

sm5.2

sm5

001

sm001

005

sm005

Press the button once.

[-1

ylnoDELdeR

[-2

DELneerg/deR

tuptuonehwDER(

)NOsnrut1

Press the button once.

■ Preset Value Input Mode

Determine the preset values.

● Auto-tuning mode (F-1)

1. In measurement mode with the

current measured value dis-

played, press . The AP-40

enters the preset value input

mode.

2. “A” and the current preset value

flash alternately.

3. Position the target at the desired

upper (lower) limit.

4. Press

to register the value.

The updated value is displayed

for 1 second.

5. “b” and the current preset value

flash alternately.

6. Position the target at the desired

lower (upper) limit.

7. Press

to register the value. The updated value is displayed for 1

second.

8. “C” and the calculated preset value C flash alternately. (You can

change the C value to any value between A and b using

▲

▼

9. Press to register the C value. The setting procedure is com-

pleted and the unit returns to measurement mode.

* To confirm the preset value, press repeatedly.

• Example of auto-tuning mode setting: Confirmation of work

piece pick-up.

Set the upper limit (A) to the position where the work piece is taken.

Set the lower limit (b) to the position where the nozzle becomes open

after releasing the work piece. Press

to register the upper and

lower limit values. The C value is automatically set to the midpoint

between the upper and lower limit values.

■ Hysteresis Mode (F-2), 2-independent Output

Mode (F-3), Window Mode (F-4)

1. In measurement mode with the

current measured value displayed,

press . The AP-40 enters the

preset value input mode.

2. “H”

and the current preset value

flash alternately.

3. Use

▲

▼

to change the value

to the desired value. Press to

4. “h”

and the current preset value

flash alternately.

5. Use

▲

▼

to change the value

to the desired value. Press to

6. “P”

and the shift value of the

zero-shift adjustment flash

alternately.

8. Press to complete the setting procedure and return to measure-

ment mode.

* To confirm the preset value, press repeatedly.

❋ ❋ ❋ ❋

• • •

(Measurement mode)

Current value

Flashes

alternately

Flashes

alternately

Flashes

alternately

Current upper

(lower) limit

value A

Current upper

(lower) limit

value b

The set value

C displays.

(C=

A + b

)

The updated value displays for 1 sec.

❋ ❋ ❋ ❋

• • •

(Measurement mode)

Flashes

alternately

Current value

Flashes

alternately

Set the desired value

using

❋ ❋ ❋ ❋

Flashes

alternately

Set the desired value

using

• • •

[Example: In hysteresis mode]

1. “A” appears in the 2-independent

output mode.

2. “b” appears in the 2-independent

output mode.

“L” appears in the window mode.

3. Shown with Z type only.

* The setting is saved

in the EEPROM.

▲

* When the units are changed, the preset values are automatically

converted to appropriate values for the updated units.

Press the button once.

* The setting is saved

in the EEPROM.

Press the button once.

1-F

edomgninut-otuA

3-F

tnednepedni-2

edomtuptuo

2-F

edomsiseretsyH

4-F

edomwodniW

Note 1: When the operation mode is changed, check the preset values

in the preset value input mode.

Note 2: Perform the zero-shift adjustment periodically.

Note 3: The initial output voltage may fluctuate by ±1.0% immediately

after the power is turned on. To measure minute differences in

pressure, let the sensor warm up for approximately 15 to 30 minutes.

Note 4: The amount of zero shift ("P") is displayed without multiplica-

tion even in the zero-shift focus mode.

1 2 3 4 5

Kommentare zu diesen Handbüchern

Keine Kommentare

Keyence AP-40P Bedienungsanleitung Seite 4

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sensoren Keyence AP-40P