Keyence DL-RS1A/IL Bedienungsanleitung PDF herunterladen (Seite 16)

Parameters of Commands and Responses

141 Hysteresis

**.***

(***.**)

((****.*))

6R/W

0 to 99.999

(0 to 999.99)

((0 to 9999.9))

0.000 (0.00)

((0.0))

142 Analog output scaling

*1R/W

0: Initial state

1: Free range

2: Bank

143 Analog output - upper limit value

*5 *10

±**.***

(±***.**)

((±****.*))

7R/W

-99.999 to +99.999

(-999.99 to +999.99)

((-9999.9 to +9999.9))

10.000 (100.00)

((1000.0))

144 Analog output - lower limit value

*5 *10

7R/W

-10.000 (-100.00)

((-1000.0))

145 External input

*11

*1R/W

0: Initial state

1: User setting

146 External input 1

*11

*1R/W

0: Zero shift input

1: Bank A input

2: Bank B input

3: Laser emission stop input

4: Not used

147 External input 2

*11

*1R/W

0: Reset input

1: Bank A input

2: Bank B input

3: Laser emission stop input

4: Not used

148 External input 3

*11

*1R/W

"0: Timing input

1: Bank A input

2: Bank B input

3: Laser emission stop input

4: Not used

149 External input 4

*11

*1R/W

0: Not used

1: Bank A input

2: Bank B input

3: Laser emission stop input

150 Bank switching method * 1 R/W

0: Button

1: External input

152 Zero shift value memory function * 1 R/W

0: OFF

1: ON

153 Mutual interference prevention function

*1R/W

0: Interference prevention OFF

1: Interference prevention ON

154 Display columns * 1 R/W

0: Initial settings

2: 0.001

3: 0.01

4: 0.1

5: 1

155 Power saving function * 1 R/W

0: OFF

1: Half

2: All

156 Head display mode * 1 R/W

0: Initial state

1: OK/NG display

2: OFF

157 Display color * 1 R/W

0: GO Green

1: GO Red

2: Always red

158 Timer duration of diff. count filter **** 4 R/W 2 to 9999 10

159 Cutoff frequency of high-pass filter * 1 R/W

0: 0.1Hz

1: 0.2Hz

2: 0.5Hz

3: 1Hz

4: 2Hz

5: 5Hz

6: 10Hz

7: 20Hz

8: 50Hz

9: 100Hz

161 Alarm setting * 1 R/W

0: Initial state

1: Clamp

2: User setting

162 Alarm count **** 4 R/W 2 to 1000 7

Data

number

Data name

Data

type

Number of

characters

Attribute

Readout range

*14

Initial

value

*14

Parameters of Commands and Responses

*1 In the Data format column, "±" indicates that the value can be either "+" or "-" and "*" signifies a

number from "0 to 9". The values shown in parentheses apply for the IL-300/600, and the values

shown in double parentheses apply for the IL-2000.

*2 Indicates that the data can only be read from (R), can only be written to (W), or can be both

read from and written to (R/W) the sensor amplifiers.

*3 The request is executed only when the data is changed from 0 to 1. To re-execute the request,

first change the setting to 0, then change it to 1. Otherwise, the request is not executed. If the

sensor amplifier is turned off after a zero shift operation, the system returns to the status which

existed prior to the zero shift. In order to maintain the shift condition even after a power off, the

"zero shift status save" function must be set to ON.

*4 The system parameter means the polarity of judgment output and the setting for analog output.

*5 Writing data to the expansion unit results in a communication error (error number: 22).

*6 Enabled when "Analog output scaling" is set to "Bank".

*7 Enabled when "Bank switching method" is set to "Button".

*8 Only when data 0 is written and the external input is OFF for wiring, it operates as OFF.

*9 Specify the system parameter set when data number 06 (System parameter set request) is

written. Convert the two digit number (ASCII characters) to a binary number and check the ON/

OFF state of each bit to specify the system parameter.

When the specified data is "006":

"6" converted to binary number is "0110".

Therefore, the setting of the amplifier to which the data is written is "NPN output" and "Analog

output 1 to 5 V".

*10 Enabled when "Analog output scaling" is set to "Free range".

*11 To reflect the setting written for the data number 146 to 149 to the sensor amplifier, write 1 (user

setting) for the data number 145 or set the external input setting to "User setting" with the button

operation on the sensor amplifier.

*12 Correction is not possible if the setting is changed between the 1st and 2nd execution requests.

If a correction is desired, avoid making setting changes during the correction operation.

*13 Execution requests are enabled only if the "Calibration function" is set as "User setting".

Moreover, these requests can be executed only if the "Calibration function" is set as "Calculated

two-point calibration" and "Calculated three-point calibration".

*14 The values shown in parentheses apply for the IL-300/600, and the values shown in double

parentheses apply for the IL-2000.

Bit Initial setting details

0 0: NPN output, 1: PNP output

3, 2, 1

000: Analog output OFF

001: 0 to 5 V

010: -5 to +5 V

011: 1 to 5 V

100: 4 to 20 mA

Reference

Bit 3, 2, 1: 1 to 5 V Bit 0: NPN output

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Kommentare zu diesen Handbüchern

Keine Kommentare

Keyence DL-RS1A/IL Bedienungsanleitung Seite 16

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sensoren Keyence DL-RS1A/IL