Keyence FS-N10 Series Bedienungsanleitung Seite 62
- Seite / 116
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
4-3 Detection Settings (Func)
4
Settings for Advanced Functions
4-16
- Digital Fiber Sensor FS-N10 Series User's Manual -
Edge detection mode
In the edge detection mode, the sensor amplifier detects changes of received light
intensity over a fixed period.
This mode is used to turn on the output only when a workpiece is moving into or out of
the detection range of the fiber unit.
• Turning the output ON when the received light intensity attenuates.
→ Select "~L_d" (Falling edge detect mode)
• To turn the output ON when the received light intensity increases:
→ Select "_|~d" (Rising edge detect mode)
Timing chart
Combining the edge detection mode and any of the functions below
makes it more difficult to detect gradual changes in light intensity.
• If the interference prevention is "dobL" (double):
"Interference Prevention" (page 4-33)
• If the eco mode is "FuLL" (Full):
"Power Save" (page 4-31)
Sensitivity setting
1
Press the [SET] button with no workpiece present.
The amplifier is now configured to ignore
changes in received light intensity for the dura-
tion that the [SET] button is pressed.
Calibration is complete after the setting value
flashes momentarily, and then stops (lights up).
• When detecting workpieces run-
ning on a conveyor, the [SET] button can be pressed for a longer period
to ignore the fluctuations of received light intensity due to conveyor vibra-
tion.
• If the setting value is so low that objects other than the workpiece of interest
are also detected, fine adjustments can be made with the button.
Refer to page 4-2 "Detection Settings (Func)" for setting methods.
When the falling edge detection mode is selected with a thrubeam model:
(1), (3):
The output is OFF because the
received light intensity is not
changing.
(2) :
The output is ON because the
received light intensity is decreasing.
(4) :
The output remains OFF because
the received light intensity is
changing but is increasing.
Operation example
(1) (2) (3) (4)
OFF
ON
Control output
Received light intensity
Point
Reference
- FS-N10 Series 1
- Introduction 2
- Safety Precautions 3
- Manual Organization 5
- Table of Contents 6
- Chapter 5 Specifications 8
- Chapter 6 Appendix 8
- Before Using 9
- Checking the Package Contents 10
- Part Names 11
- Display/control unit 12
- Model Number Description 13
- Fiber Units 14
- Installation and Connection 15
- Installing Sensor Amplifiers 16
- Main unit Expansion unit 17
- Monitor output 18
- Connecting the Fiber Unit 20
- Basic Operation 23
- 3-1 Quick Reference 25
- Switching Output 26
- Adjusting Sensitivity 27
- Enabling the preset function 28
- Disabling the preset function 28
- Impotant 29
- Current value is " 29
- Workpiece 30
- Full Auto Preset Function 31
- Full Auto Calibration 35
- Percentage calibration 37
- Zero shift calibration 37
- Current vallue is " 38
- Saturation Canceling function 40
- Selecting Recipe 41
- Initialization 43
- Locking in MEGA Mode 44
- Disabling the Key Operation 45
- Key Lock with PIN Number 46
- List of Settings 48
- Basic Settings 50
- Setting example 52
- Detection Settings (Func) 53
- Detection Mode 54
- The DTM indicator 55
- Display changes 55
- 100.0" 55
- .0" 57
- Display example 59
- Area detection mode 60
- Edge detection mode 62
- External Input 63
- Thrubeam model 64
- Sleep function 65
- Normal display 69
- Inverted display 69
- Select L-on/D-on 70
- No operation for 3 70
- Sub-display 70
- Excess gain (%) display 71
- Light intensity hold display 71
- Setting value 72
- Received light 72
- Peak value 72
- Excess gain hold (%) display 73
- L-on / D-on display 73
- Preset Saturation Function 74
- System Settings (SYS) 76
- Power Save 77
- Display Gain 78
- Interference Prevention 79
- 2-output Settings ( ) 81
- Limit setting output mode 82
- Warning output mode 83
- Output Timer for Output2 84
- Settings Save/Recall 85
- User Reset (Settings Recall) 86
- Specifications 87
- 2-Output Type 89
- Monitor Output Type 90
- Zero Line Type 91
- Input/Output Circuit Diagram 92
- Monitor output type 93
- Dimensions 94
- /N13CP/N14CP 95
- FS-N11EN/12EN 96
- End unit (OP-26751) 97
- When mounted on DIN rail 97
- 5-3 Dimensions 98
- Troubleshooting 100
- 6-1 Troubleshooting 101
- Appendix 101
- L_d selected) 50 4-16 104
- Reference 105
- 6-5 Index 109
- Quick Reference 110
- List of settings 112
- WARRANTIES AND DISCLAIMERS 115
Verwandte Produkte und Handbücher für Sensoren Keyence FS-N10 Series
Sensoren Keyence FU-A100 Bedienungsanleitung
(1 Seiten)
(1 Seiten)
Sensoren Keyence FS-21X Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Sensoren Keyence FS-22X Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Sensoren Keyence FS-10 Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Sensoren Keyence LV-N10 Series Bedienungsanleitung
(112 Seiten)
(112 Seiten)
Sensoren Keyence LV-S63 Bedienungsanleitung
(1 Seiten)
(1 Seiten)
Sensoren Keyence LV-SA Bedienungsanleitung
(10 Seiten)
(10 Seiten)
Sensoren Keyence LV-SB Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Sensoren Keyence LV Series Bedienungsanleitung
(10 Seiten)
(10 Seiten)
Sensoren Keyence LV-B302 Bedienungsanleitung
(1 Seiten)
(1 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern