Keyence AP-C30KP Bedienungsanleitung PDF herunterladen (Seite 5)

. Ambient Pressure Compensation

Open the applied pressure to the surrounding air so that it equals the

ambient pressure and press the button for 3 seconds or more

while the current value or reference value is being displayed.

The ambient pressure point will be corrected.

*1 Ambient pressure can be corrected within a range of ±5 % of F.S.

When atmospheric pressure compensation has been performed, the

settings will be saved even when power to the sensor is turned off.

*2 AP-C31K/C31KP/C33K/C33KP: Can be used during focus mode op-

eration as well. Values will be compensated based on the center pres-

sure.

. Key Lock

Disables operations that would modify the sensor's configuration. Display

content can be toggled.

Pressing and holding either or for at least 3 seconds while pressing

button will lock the keypad and cause the display to flash.

*The same key combination will deactivate the key lock feature.

. Specifications

Unit

kPa

kgf/cm

mmHg

inHg

psi

bar

Unit

kPa

kgf/cm

mmHg

inHg

psi

bar

kPa

kgf/cm

mmHg

inHg

psi

bar

kPa

kgf/cm

mmHg

inHg

psi

bar

Negative pressure

Positive pressure

AP-C30K/C30KP

AP-C31K/C31KP AP-C33K/C33KP

500kPa 500kPa

1.5MPa

Air, non-corrosive gasses

Gauge pressure

12 to 24 VDC±10% Ripple (P-P) 10% max.

3.5 digit two-color 7 segment LED

(11 mm character height) Display cycle: 10 times/second

-10 to +110 % of F.S. -15 to +110 % of F.S.

Red LED x 2 (supports control output 1 / control output 2)

± 0.2 % of F.S.

Variable (standard 0.5% of F.S.)

± 1 % of F.S. max.

Selectable from 2.5, 5, 100, 500 ms

No-voltage input (without contacts)

Input time 2 ms or greater (Switchable with analog output.)

NPN open collector max. 100 mA (40 V max.)

residual voltage 1 V max., 2 outputs (NO/NC switchable)

PNP open collector Max. 100 mA (30 V max.)

residual voltage 1 V max., 2 outputs (NO/NC switchable)

1to 5 V Output impedance 1 kΩ max. (Switchable with zero shift input.)

0 to +50 °C (No freezing)

35 to 85 % RH (No condensation)

10 to 55 Hz, compound amplitude 1.5 mm, 2 hours for each of XYZ axes

NPT 1/8 Bidirectional rotating type

Front case: polysarfun; Rear case: PBT;

Front sheet: polycarbonate; Pressure port: die-cast zinc

30 g (not including cables) / 78 g (including 2-m cable)

Power cord (2-m, connector type) Units sticker

Type

Model

Pressure resistance

Adaptive fluids

Pressure type

Power supply voltage

Current

consumption

Display method

Configuration/display range *

Operating status indicators

Repeatability

Hysteresis *

Display temperature characteristics

Response (chatter prevention feature)

Zero shift input

Control output *

Analog output

Housing material

Weight

Accessories

Multi-range

Negative pressure

Positive pressure

Negative pressure

Positive pressure

Compound pressure

0 to -101.3

0 to -1.033

0 to -760

0 to -29.9

0 to -14.69

0 to -1.013

0.1

0.001

0.1

0.02

0.001

0 to 100.0

0 to 1.020

0 to 750

0 to 29.5

0 to 14.50

0 to 1.000

0.1

0.001

0.1

0.02

0.001

101.3 to -101.3

1.033 to -1.033

760 to -760

29.9 to -29.9

14.69 to -14.69

1.013 to -1.013

0.2

0.002

0.1

0.04

0.002

0 to -101.3

0 to -760

0 to -29.9

0 to -14.69

0 to -1.013

0 to

1.000MPa

0 to 10.20

0 to 145.0

0 to 10.00

0.1

0.02

0.001

0.01

0.1

0.01

0.002

0.1mbar

0.01

0.2

0.01

0.1

0.001

0.02

0.001

0.001MPa

Eco mode

480 mW(40 mA)/600 mW(50 mA) max. 720 mW(30 mA)/960 mW(40 mA) max.

Normal

720 mW(60 mA)/900 mW(75 mA) max.

960 mW(40 mA)/1320 mW(55 mA) max.

12 V operation(NPN/PNP) 24 V operation(NPN/PNP)

Rated pressure range

Rating

Resolution

Multi-range Standard mode Focus mode

Environmental

resistance

Ambient temperature

Relative humidity

Vibration

Pressure port

*1 During focus mode operation, restricted to focus range.

*2 During focus mode operation, standard 0.2% of F.S.

*3 The AP-C30K(P), C31K(P), and C33K(P) use PNP output.

. Error Displays and Corrective Actions

■ Error displays during normal operation

• No difference in sensitivity

(during 2 point tuning/active

tuning).

• There is an applied pressure

of ±5 % of F.S. during ambient

pressure compensation.

• An excess current is flowing to the

control output.

• Reading is falling below

(exceeding) configuration/display

pressure range.

• Reading is exceeding (falling

below) configuration/display

pressure range.

• When there were not at least 2

shift inputs during active 2 point

tuning.

Adjust the air pressure device so that

there will be a difference in sensitivity.

(Return to atmospheric pressure.)

Repeat atmospheric compensation.

Check the load and return it to the

rated range.

Return the pressure to the rated

pressure range.

Return the pressure to the rated

pressure range.

Repeat the active tuning procedure

so that there are at least 2 shift inputs.

Display Cause Solution

* Contact KEYENCE for information about error displays other than those

described above.

. Default Mode Settings (Initialization)

The sensor ships with the following configuration.

AP-C30K AP-C30K

AP-C31K(P)/

C33K(P)

AP-C31K(P)/

C33K(P)

Detection

range

Units

Detection

mode

Operating

mode

N.O./N.C.

switching

Analog/

zero shift

Chatter pre-

vention

Display

color

Power-

save

*Press button 5 times while holding down the button to return the

sensor to its default configuration.

WARRANTIES AND DISCLAIMERS

(1) KEYENCE warrants the Products to be free of defects in materials and workmanship for a period

of one (1) year from the date of shipment. If any models or samples were shown to Buyer, such models

or samples were used merely to illustrate the general type and quality of the Products and not to

represent that the Products would necessarily conform to said models or samples. Any Products found

to be defective must be shipped to KEYENCE with all shipping costs paid by Buyer or offered to KEYENCE

for inspection and examination. Upon examination by KEYENCE, KEYENCE, at its sole option, will

refund the purchase price of, or repair or replace at no charge any Products found to be defective. This

warranty does not apply to any defects resulting from any action of Buyer, including but not limited to

improper installation, improper interfacing, improper repair, unauthorized modification, misapplication

and mishandling, such as exposure to excessive current, heat, coldness, moisture, vibration or outdoors

air. Components which wear are not warranted.

(2) KEYENCE is pleased to offer suggestions on the use of its various Products. They are only

suggestions, and it is Buyer’s responsibility to ascertain the fitness of the Products for Buyer’s intended

use. KEYENCE will not be responsible for any damages that may result from the use of the Products.

(3) The Products and any samples (“Products/Samples”) supplied to Buyer are not to be used

internally in humans, for human transportation, as safety devices or fail-safe systems, unless their

written specifications state otherwise. Should any Products/Samples be used in such a manner or

misused in any way, KEYENCE assumes no responsibility, and additionally Buyer will indemnify KEYENCE

and hold KEYENCE harmless from any liability or damage whatsoever arising out of any misuse of the

Products/Samples.

(4) OTHER THAN AS STATED HEREIN, THE PRODUCTS/SAMPLES ARE PROVIDED WITH NO OTHER

WARRANTIES WHATSOEVER. ALL EXPRESS, IMPLIED, AND STATUTORY WARRANTIES, INCLUDING,

WITHOUT LIMITATION, THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE, AND NON-INFRINGEMENT OF PROPRIETARY RIGHTS, ARE EXPRESSLY DISCLAIMED. IN

NO EVENT SHALL KEYENCE AND ITS AFFILIATED ENTITIES BE LIABLE TO ANY PERSON OR ENTITY

FOR ANY DIRECT, INDIRECT, INCIDENTAL, PUNITIVE, SPECIAL OR CONSEQUENTIAL DAMAGES

(INCLUDING, WITHOUT LIMITATION, ANY DAMAGES RESULTING FROM LOSS OF USE, BUSINESS

INTERRUPTION, LOSS OF INFORMATION, LOSS OR INACCURACY OF DATA, LOSS OF PROFITS, LOSS

OF SAVINGS, THE COST OF PROCUREMENT OF SUBSTITUTED GOODS, SERVICES OR TECHNOLOGIES,

OR FOR ANY MATTER ARISING OUT OF OR IN CONNECTION WITH THE USE OR INABILITY TO USE

THE PRODUCTS, EVEN IF KEYENCE OR ONE OF ITS AFFILIATED ENTITIES WAS ADVISED OF A POSSIBLE

THIRD PARTY’S CLAIM FOR DAMAGES OR ANY OTHER CLAIM AGAINST BUYER. In some jurisdictions,

some of the foregoing warranty disclaimers or damage limitations may not apply.

0115-2 96M1038

Printed in Japan

KEYENCE CORPORATION OF AMERICA

PHONE: 201-930-0100

FAX: 201-930-0099

KEYENCE DEUTSCHLAND GmbH

PHONE: 06102-36 89-0

FAX: 06102-36 89-100

KEYENCE (UK) LIMITED

PHONE: 01908-696900

FAX: 01908-696777

KEYENCE FRANCE S.A.

PHONE: 01 56 37 78 00

FAX: 01 56 37 78 01

KEYENCE ITALIA S.p.A.

PHONE: 02-668-8220

FAX: 02-668-25099

KEYENCE SINGAPORE PTE LTD.

PHONE: 6392-1011

FAX: 6392-5055

KEYENCE (MALAYSIA) SDN BHD

PHONE: 03-2092-2211

FAX: 03-2092-2131

KEYENCE (THAILAND) CO., LTD.

PHONE: 02-369-2777

FAX: 02-369-2775

KEYENCE TAIWAN CO., LTD.

PHONE: 02-2718-8700

FAX: 02-2718-8711

KEYENCE (HONG KONG) CO., LTD.

PHONE: 3104-1010 FAX: 3104-1080

KEYENCE INTERNATIONAL TRADING

(SHANGHAI) CO., LTD.

PHONE: 021-68757500

FAX: 021-68757550

KOREA KEYENCE CO., LTD.

PHONE: 02-563-1270

FAX: 02-563-1271

KEYENCE CORPORATION

1-3-14, Higashi-Nakajima, Higashi-Yodogawa-ku,

Osaka, 533-8555, Japan

PHONE: +81-6-6379-2211 FAX: +81-6-6379-2131

AFFILIATED COMPANIES

1 2 3 4 5

Kommentare zu diesen Handbüchern

Keine Kommentare

Keyence AP-C30KP Bedienungsanleitung Seite 5

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sensoren Keyence AP-C30KP