Keyence KV Series Bedienungsanleitung Seite 187
- Seite / 240
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Appendices
2-163
1
Appendices
Appendix B Instruction List
This appendix includes a list of instructions and an outline of their processes. For
details, refer to Chapter 2, "Instructions" on page 3-33.
B-1 Basic instructions
Instruction name Mnemonic Outline of process
Load LD Connects N.O. contact to bus.
Load Bar LDB Connects N.C. contact to bus.
Out OUT Outputs ON/OFF status of input to relay coil.
Out Bar OUB Outputs inverted ON/OFF status of input to relay coil.
And AND Connects N.O. contact in series.
And Bar ANB Connects N.C. contact in series.
Or OR Connects N.O. contact in parallel.
Or Bar ORB Connects N.C. contact in parallel.
And Load ANL Connects in series the blocks made of one or more
contacts.
Or Load ORL Connects in parallel the blocks made of one or more
contacts.
Set SET Turns ON specified relay forcibly, and enables it to
remain ON.
Reset RES Turns OFF specified relay forcibly.
Timer TMR Sets an on-delay timer that counts down in 0.1 s
increments.
High-Speed Timer TMH Sets an on-delay timer that counts down in 0.01 s
increments.
High-Speed 1-ms TMS Sets an on-delay timer that counts down in 0.001 s
Timer increments.
Counter C Sets an up counter.
Up-Down Counter UDC Sets an up-down counter.
Differentiate Up DIFU Detects rising edge of input signal and turns ON
specified relay for first scan time only.
Differentiate Down DIFD Detects falling edge of input signal and turns ON
specified relay for first scan time only.
Keep KEEP Turns ON specified relay when SET input relay turns
ON, and enables this relay to remain ON. Turns OFF
specified relay when RESET input relay turns ON.
Shift SFT Sets a shift register.
High Speed HSP Shortens time constant of specified input relay to be
ready for high speed.
Master Control MC Selects ON/OFF status of relays, timers or counters
set before MCR instruction.
Master Control MCR Ends the execution of MC instruction.
Reset
Memory Switch MEMSW Sets memory switches.
No Operation NOP Performs no operation.
End END Indicates end of each routine in the program.
End Hi ENDH Indicates end of entire program.
KVSKA Appendix.P65 08.3.11, 11:26 AM163
- Support software 1
- Safety Precautions 2
- WARRANTIES AND DISCLAIMERS: 2
- Note to User 3
- )222-1.p("07NUF 7
- How this manual is organized 8
- Programming 9
- Contents 10
- Chapter 3 Simulator 11
- Chapter 4 Monitor 11
- Appendices 12
- Installation 13
- Chapter 6 Handheld Programmer 16
- Chapter 10 Troubleshooting 19
- 3 Programming 20
- Chapter 2 Instructions 21
- WARRANTIES AND DISCLAIMERS 24
- Chapter 1 25
- See page 2-7 26
- Chapter 1 Introduction 27
- 1.3 Before Programming 31
- 1.4 Installing the Software 33
- 1.4.2 Installation procedure 34
- 1.5 Cautions for Use 36
- 1.6 Basic Operations 37
- To start up the software 39
- Change Models 40
- 1.6.3 Screen 41
- Display mode 42
- Show/hide comments 44
- 1.6.5 Online help 45
- Chapter 2 49
- 2.2 Edit Screen 51
- Line No 52
- Step No 52
- Scroll bar 52
- 2.3 File Management 53
- Auto Read 54
- Set Auto Save 55
- Save, File 56
- Save As 56
- Reading files 57
- Other Format 58
- Read Other File Comment 58
- 2.3.7 Verifying files 60
- 2.4.1 Entering symbols 61
- Symbol Input 62
- Symbol Selective Input (Tab) 62
- Relay 2008 64
- Symbol Direct Input (Enter) 65
- 2.4.2 Deleting symbols 66
- Entering coils 67
- Entering connection lines 68
- Deleting connection lines 69
- Comment 70
- Selecting the range (p. 2-52) 72
- Radio buttons 72
- Display mode (p. 2-19) 73
- Selecting the range (p.2-52) 75
- 2.6 Edit and Arrangement 76
- Copy/move/delete operation 78
- Step 3 on page 2-56 78
- Inserting blank lines 81
- Deleting lines 81
- Line/Step No 82
- Jump to the first/last line 83
- Jump to the registered line 83
- Find (Ctrl + F) 86
- Replace Operand (Ctrl + R) 88
- 2.7.5 Converting a/b contacts 89
- Edit List 91
- Terminating a mnemonic list 92
- Format of a mnemonic list 92
- 2.8.2 Copy, move, and delete 93
- Usage Information 94
- System Settings 95
- 2.11.1 Creating a macro file 96
- What are temporary devices? 97
- Macro Input 98
- Develop (Shift + F1) 98
- Compile 99
- Compile (Ctrl + F9) 99
- 2.12.2 Error display 100
- 2.12.3 Double coil check 100
- Print (Ctrl + P) 101
- Chapter 2 Editor 102
- File (F) 105
- Print Preview (V) 105
- Change Ladder Diagram Color 106
- Chapter 3 107
- Chapter 3 Simulator 108
- Device all clear (p. 2-108) 109
- Simulator (Ctrl + F2) 110
- Editor (Ctrl + F1) 111
- Sample screen 112
- Ladder Monitor 113
- Ladder monitor window 114
- Step No. being executed 115
- Operation mode being executed 115
- Scan time 115
- Execute 116
- Execute Continuous Scan (F5) 116
- Execute One Scan (F9) 117
- 0000 0000 118
- Setting break conditions 122
- Setting the scan time 124
- Setting the watch dog timer 124
- 3.3.3 Executing steps 125
- Executing a step once 126
- Jump in Ladder Monitor 129
- Search in Ladder Monitor 130
- Cross reference search 131
- Device all clear 132
- Monitor All 133
- Reading the monitor all file 135
- Monitor All 137
- Selecting devices 140
- Turning on/off bit devices 141
- Resetting devices 142
- Registration Monitor 143
- Save Window As 144
- Open Window 145
- 3.5.4 Registering devices 146
- Turning on/off the bit device 148
- Right-click (Copy Attribute) 149
- Moving devices 150
- Deleting devices 151
- Sorting devices 151
- Before deletion 151
- After deletion 151
- Settings 153
- Wait Time 154
- Print Preview 155
- Executing printout 156
- Chapter 4 157
- Chapter 4 Monitor 158
- p. 2-136 159
- Setting the serial port 160
- Set Machine Number 161
- Communication Setup 162
- Set Comment Transfer 162
- Transferring programs 163
- Reading programs 165
- Exit procedure 166
- 4.4.4 Starting the monitor 169
- 4.4.5 Stopping the monitor 169
- Status indication 170
- Operation (RUN mode) 171
- Stop (STOP mode) 171
- 4.6 Monitor Function 173
- Change All 174
- Reading devices from the PLC 175
- Writing devices to the PLC 175
- Saving/reading devices 175
- 4.6.3 Device all clear 178
- Appendix A Error Message List 180
- A-3 File errors 181
- A-4 Installation errors 181
- A-8 PLC errors 184
- Appendix B Instruction List 187
- B-2 Application instructions 188
- B-3 Arithmetic instructions 189
- B-4 Interrupt instructions 190
- Appendix C Relay No. List 191
- D-5 Memory switches 196
- D-6 Special memory list 196
- E-1 Special utility relays 198
- E-2 Memory switches 200
- E-3 Special memory list 200
- Appendix G Quick Reference 204
- G-2 Simulator 212
- G-3 Monitor 219
- Appendix I List of Files Used 228
Kommentare zu diesen Handbüchern
Verwandte Produkte und Handbücher für Sensoren Keyence KV Series
Sensoren Keyence KV-D20 Bedienungsanleitung
(72 Seiten)
(72 Seiten)
Sensoren Keyence MS-F07 Bedienungsanleitung
(2 Seiten)
(2 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Hi