Keyence LS-3100/3100W Series Bedienungsanleitung Seite 83
- Seite / 104
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
77
Compatibility
• With the LS series, the controller and scanning head are calibrated as a
pair. To satisfy the specifications, therefore, be sure to combine a control-
ler and scanning head having the same serial number.
• The transmitter and receiver are also calibrated as a pair.
• When using 2 scanning heads, connect them respectively to the specified
connector port of the controller.
CHAPTER 7 Hints on Correct Use
Operating Environment
• Be sure to operate the LS controller in a place where the temperature is
within a range between 0 and 45°C. (0 to 40°C for LS-3036/3060)
• Fluctuation in ambient temperature may cause measurement error.
Always maintain the ambient temperature at a constant level. If the
ambient temperature changes by 10°C, it takes approx. 60 minutes for the
temperature distribution in the LS controller to become uniform.
• Be sure to keep the laser emitting surface (transmitter) and the laser
receiving surface (receiver) free from any substance refracting light (such
as water or oil).
• Blow off dirt or dust on the protective glass using clean air. If dirt or dust
still remains, wipe it off using a soft cloth moistened with alcohol.
• The protective glass can be replaced. See the figure below to replace the
glass.
Countermeasures against
Noise
• Do not mount the scanning head to the place where a certain level of
electrical noise is applied or transferred. Isolate the scanning head if
electrical noise may be occured. Otherwise, laser diode may deteriorate
or become damaged.
• Keep the wiring or connection cable away from high-voltage lines or
power lines to prevent the LS controller from malfunctioning because of
noise.
• Be sure to earth-ground the LS controller through the earth ground termi-
nal (No. 19). Insulating the scanning head is also effective in reducing
noise.
Fuse
When the fuse is blown, replace it with the following one:
Midget fuse: F-7142 2A or equivalent
Cooling Fan
Do not block the cooling fan on the back panel. Blocking it will overheat the
LS controller, causing malfunction.
ls3100_76_88.p65 08.10.1, 10:57 AM77
- LS-3100(W) Series 1
- Unpacking 3
- WARRANTIES AND DISCLAIMERS 3
- CONTENTS 4
- Chapter 8 Error Messages 78 6
- Appendices 83 6
- WARRANTIES AND DISCLAIMERS 97 6
- LASER SAFETY PRECAUTIONS 7
- 1-4 Safety Consideration 8
- 1-3. Label Location 8
- LS-3060LS-3060 9
- LS-3032, LS-3034, LS-3036 10
- LS-3033, LS-3033 SO, LS-3060 10
- Grounding the 11
- Serial No 12
- Connect the correct scanning 12
- CHAPTER 2 13
- TRIAL OPERATION 13
- CHAPTER 3 14
- QUICK SETUP PROCEDURES 14
- 3-1. Common Settings 15
- 3-2. Measurement Procedures 16
- Gap Measurement 1 17
- Gap Measurement 2 17
- MODE NOMAL 18
- MODE P–P 18
- SEG D I A 18
- S E G E DGE1 18
- Measuring Target 19
- Displacement within 19
- Measuring Edge 19
- Movement 19
- Measuring Outer Diam 20
- Front Panel 21
- LS-3100 Series 21
- Back Panel 22
- LS-3033T 23
- LS-3033R 23
- 4-2. Indicators and Displays 24
- 4-3. Panel Keys 25
- See P.39 26
- See P.20 26
- See P.43 26
- Averaging Methods 27
- Analog Voltage Range 28
- See P.32 29
- See P.63, 64 30
- See P.63 30
- See P.29 31
- DIGIT SUPPRESS 32
- BAUD RATE 33
- POSITION CHECK 34
- Definition of Segment 36
- Description 36
- SEG ( 3 , 3 ) 37
- Segment Selector 38
- See P.31 39
- See P.31 40
- Segment Check 41
- Output Channel 43
- See P.43 or OFFSET value 44
- Transmitter 44
- Receiver 44
- MODE, OFFSET, and LIMIT 45
- C MODE Key 46
- 35 2. 345 50
- 2 36 1. 234 50
- G PROG (Program) 51
- See P.62 52
- Analog Voltage Output 53
- Comparator Output 53
- Specifications 55
- Pin Assignment 55
- Remote Operation 56
- Measurement in "mm" 60
- SP SP 6 0 . 0 0 0 0 63
- -SP60 . 0000C 63
- SP SP 1 0 . 0 0 0 0 CR 65
- -SP10 . 0000CR 65
- 1st data 2nd data 66
- Pin assignment 68
- Input Signal 69
- Output Signal 69
- Control Input Terminals 70
- Control Output Terminals 70
- MOUNTING SCANNING HEAD 71
- OS TP IOI N CHECK 72
- LED 7 lights 73
- CHAPTER 6 74
- OPTIONAL INTERFACE BOARDS 74
- 6-1. BCD Output 74
- External Trigger Input 76
- (EXT TRIG IN) 76
- Setting Address 78
- Setting Talk Only Mode 78
- Setting Delimiter 78
- Values or Other Data 79
- Talk Only Mode 79
- Setting Functions and 79
- Outputting Measured 79
- Status Byte 80
- Example of Program 81
- GP-IB Interface I/O 82
- Measuring Conditions 82
- CHAPTER 8 84
- ERROR MESSAGES 84
- CHAPTER 8 Error Messages 85
- CHAPTER 9 86
- TROUBLESHOOTING GUIDE 86
- OPERATING PRINCIPLE 89
- CHARACTERISTICS 90
- Temperature 91
- Characteristics 91
- (Typical) 91
- SPECIFICATIONS 92
- Scanning Head 93
- Approx.34 94
- APPENDIX E 95
- QUICK REFERENCE TABLE 95
- KEY FLOWCHARTS 97
- APPENDIX F Key Flowcharts 98
- FNC (Function) 100
- APPENDIX F Key Flowcharts 101
- APPENDIX F Key Flowcharts 102
- SAFETY PRECAUTIONS 103
Verwandte Produkte und Handbücher für Sensoren Keyence LS-3100/3100W Series
Sensoren Keyence GP-M Series Bedienungsanleitung
(28 Seiten)
(28 Seiten)
Sensoren Keyence AP-40P Bedienungsanleitung
(5 Seiten)
(5 Seiten)
Sensoren Keyence DL-CL1 Bedienungsanleitung
(78 Seiten)
(78 Seiten)
Sensoren Keyence SK-H Series Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Sensoren Keyence IV Series Bedienungsanleitung
(10 Seiten)
(10 Seiten)
Sensoren Keyence IV Series Bedienungsanleitung
(110 Seiten)
(110 Seiten)
Sensoren Keyence IV-D10 Bedienungsanleitung
(2 Seiten)
(2 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern