Keyence BL-N90 Series Bedienungsanleitung PDF herunterladen (Seite 90)

A-3 Using the Wall Mount with the Communication Unit

A-8

Appendices

When using the cup holder, install the cup holder before mounting the communication unit to

the wall.

Procedure

1 When inserting the communication unit into the cup holder, press it until it is secured in

place with the tabs.

Installing the cup holder to the communication unit

CAUTION

The cup holder holds the BL-N90 firmly in the communication unit. Be careful

when removing the BL-N90. If you pull on it too hard, the communication unit

may break or separate from the wall.

1 2 ... 85 86 87 88 89 90 91 92 93 94 95 ... 109 110

BL-N90 Series 1
Introduction 2
Laser Safety Precautions 3
Handling the BL-N90 5
Wireless Communication 6
■ Europe 7
■ North America 8
Precautions on UL and CSA 9
Maintenance 10
Table of Contents 11
Chapter 4 Program 12
Overview 15
Checking the Package Contents 16
BL-N9R BL-N9V 17
BL-N9UB 17
Specialized stand OP-82191 18
1-2 Part Names 19
Operation Check LED 20
Initial Setup 21
2-1 Initial Setup 22
Included parts 23
BL-N9UB BL-N9V/N9R 24
1 Turn on the computer 25
Installing the USB driver 26
1 Turn off the computer 27
4 Turn on your computer 28
1 Turn on your computer 29
Conversion connector 30
(D-sub 9-pin) 30
2-4 Charging the BL-N90 31
Battery low alarm 32
Continuous use capacity 32
Charging time 32
2-5 Establishing a Connection 33
Scanning a barcode 34
Swapping out the BL-N90 34
Initializing the BL-N90 35
Readable range 36
Read distance: 100 mm 36
Trigger switch 36
Operation check LED 36
Precautions for reading 37
X Incorrect Scan 37
X Incorrect Scan 37
Checking the Connected Pair 38
Obstacle 39
Descriptions of Key 41
Functions 41
3-1 Reading 42
Rereading prevention 43
Limit read digits 43
Buzzer tone selection 43
Number of 44
BL-N90 status 44
Selecting the Reading Mode 45
Detection 46
Descriptions of Key Functions 48
3-3 Sending the Reading Data 49
Inter-character Delay 50
Localized settings 51
No protocol 51
3-5 Charge Error Prevention 53
3-6 Sleep Mode 54
Configuring the Program 56
Start/End Program 57
Initialization 57
Settings for the Barcode Type 58
EAN/UPC Detailed Settings 60
Read only EAN add-on code 62
GS1-128 62
Send ]c1 symbol identifier 62
Group separator settings 62
Check digit inspection 63
Send check digit 63
Send application identifier 65
Send symbol identifier 65
4-4 Setting the Reading Mode 67
Auto-scan detection distance 68
4-5 Buzzer Settings 69
4-6 Decode Settings 70
<375 ms> 500 ms 71
Limit all settings 72
Limit individual settings 72
Block 1 settings 73
Block 2 settings 73
Block 3 settings 74
Block 4 settings 74
Block 5 settings 74
Block 6 settings 74
Block 7 settings 74
Data Format 75
<TAB prohibited> 76
<ETX prohibited> 76
<1 ms> 10 ms 76
Keyboard/USB Settings 77
RS-232C Settings 77
Stop bit length 78
Parity check 78
Communication protocol 78
4-10 Other Settings 79
4-11 Decimal Program Code 80
4-12 Code Type List 81
A-1 Specifications 84
Communication unit 85
A-2 Dimensions 86
When using the pedestal 87
When not using the pedestal 87
Mounting 88
Fix with double-sided tape 89
Procedure 90
A-4 Dedicated Stand 91
Pedestal 93
M3 screw 94
Stand fixture 96
Stand base 96
Logo plate 96
Flathead screw driver 96
7 Replace the logo plate 97
A-5 Troubleshooting 98
Problem Possible cause Remedy 99
A-6 ASCII Code Table 100
Barcode Settings 101
Setting item Setting content 102
Factory 102
Operation Settings 104
Communication Data Format 106
Other Settings 107
Connection Interface 107
Appendices 108
WARRANTIES AND DISCLAIMERS 109

Kommentare zu diesen Handbüchern

Keine Kommentare

Keyence BL-N90 Series Bedienungsanleitung Seite 90

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sensoren Keyence BL-N90 Series