Keyence BL-N90 Series Bedienungsanleitung Seite 22
- Seite / 110
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
2-2
2
Initial Setup
2-1 Initial Setup
Before using the BL-N90, the following connections must be set up.
Performing these connections establishes the following communications, enabling the BL-
N90 for use.
•
Connection between communication unit and computer:Wired communication
•
Connection between BL-N90 and communication unit: Wireless communication (Bluetooth)
z Initial setup
Note
After connecting the communication unit to the computer, be sure to charge
the BL-N90 before use.
1
Connect the power cable to the communication unit. ( page 2-3).
2
Connect the communication unit to your computer ( page 2-5).
3
Charge the BL-N90 ( page 2-11).
4
Establish a connection between the BL-N90 and the communication unit
( page 2-13).
Use the BL-N90 to read the BD address barcode attached to the
communication unit.
5
Initialize settings for the BL-N90 ( page 2-15).
Read the initialization barcode using the BL-N90.
- BL-N90 Series 1
- Introduction 2
- Laser Safety Precautions 3
- Handling the BL-N90 5
- Wireless Communication 6
- ■ Europe 7
- ■ North America 8
- Precautions on UL and CSA 9
- Maintenance 10
- Table of Contents 11
- Chapter 4 Program 12
- Overview 15
- Checking the Package Contents 16
- BL-N9R BL-N9V 17
- BL-N9UB 17
- Specialized stand OP-82191 18
- 1-2 Part Names 19
- Operation Check LED 20
- Initial Setup 21
- 2-1 Initial Setup 22
- Included parts 23
- BL-N9UB BL-N9V/N9R 24
- 1 Turn on the computer 25
- Installing the USB driver 26
- 1 Turn off the computer 27
- 4 Turn on your computer 28
- 1 Turn on your computer 29
- Conversion connector 30
- (D-sub 9-pin) 30
- 2-4 Charging the BL-N90 31
- Battery low alarm 32
- Continuous use capacity 32
- Charging time 32
- 2-5 Establishing a Connection 33
- Scanning a barcode 34
- Swapping out the BL-N90 34
- Initializing the BL-N90 35
- Readable range 36
- Read distance: 100 mm 36
- Trigger switch 36
- Operation check LED 36
- Precautions for reading 37
- X Incorrect Scan 37
- X Incorrect Scan 37
- Checking the Connected Pair 38
- Obstacle 39
- Descriptions of Key 41
- Functions 41
- 3-1 Reading 42
- Rereading prevention 43
- Limit read digits 43
- Buzzer tone selection 43
- Number of 44
- BL-N90 status 44
- Selecting the Reading Mode 45
- Detection 46
- Descriptions of Key Functions 48
- 3-3 Sending the Reading Data 49
- Inter-character Delay 50
- Localized settings 51
- No protocol 51
- 3-5 Charge Error Prevention 53
- 3-6 Sleep Mode 54
- Configuring the Program 56
- Start/End Program 57
- Initialization 57
- Settings for the Barcode Type 58
- EAN/UPC Detailed Settings 60
- Read only EAN add-on code 62
- GS1-128 62
- Send ]c1 symbol identifier 62
- Group separator settings 62
- Check digit inspection 63
- Send check digit 63
- Send application identifier 65
- Send symbol identifier 65
- 4-4 Setting the Reading Mode 67
- Auto-scan detection distance 68
- 4-5 Buzzer Settings 69
- 4-6 Decode Settings 70
- <375 ms> 500 ms 71
- Limit all settings 72
- Limit individual settings 72
- Block 1 settings 73
- Block 2 settings 73
- Block 3 settings 74
- Block 4 settings 74
- Block 5 settings 74
- Block 6 settings 74
- Block 7 settings 74
- Data Format 75
- <TAB prohibited> 76
- <ETX prohibited> 76
- <1 ms> 10 ms 76
- Keyboard/USB Settings 77
- RS-232C Settings 77
- Stop bit length 78
- Parity check 78
- Communication protocol 78
- 4-10 Other Settings 79
- 4-11 Decimal Program Code 80
- 4-12 Code Type List 81
- A-1 Specifications 84
- Communication unit 85
- A-2 Dimensions 86
- When using the pedestal 87
- When not using the pedestal 87
- Mounting 88
- Fix with double-sided tape 89
- Procedure 90
- A-4 Dedicated Stand 91
- Pedestal 93
- M3 screw 94
- Stand fixture 96
- Stand base 96
- Logo plate 96
- Flathead screw driver 96
- 7 Replace the logo plate 97
- A-5 Troubleshooting 98
- Problem Possible cause Remedy 99
- A-6 ASCII Code Table 100
- Barcode Settings 101
- Setting item Setting content 102
- Factory 102
- Operation Settings 104
- Communication Data Format 106
- Other Settings 107
- Connection Interface 107
- Appendices 108
- WARRANTIES AND DISCLAIMERS 109
Verwandte Produkte und Handbücher für Sensoren Keyence BL-N90 Series
Sensoren Keyence N-48/42 Bedienungsanleitung
(20 Seiten)
(20 Seiten)
Sensoren Keyence DV-90 Bedienungsanleitung
(262 Seiten)
(262 Seiten)
Sensoren Keyence N-400 Bedienungsanleitung
(150 Seiten)
(150 Seiten)
Sensoren Keyence N-410 Bedienungsanleitung
(160 Seiten)
(160 Seiten)
Sensoren Keyence KV Series Bedienungsanleitung
(26 Seiten)
(26 Seiten)
Sensoren Keyence KV Series Bedienungsanleitung
(240 Seiten)
(240 Seiten)
Sensoren Keyence KV-D20 Bedienungsanleitung
(72 Seiten)
(72 Seiten)
Sensoren Keyence MS-F07 Bedienungsanleitung
(2 Seiten)
(2 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.090 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern