Keyence BL-N90 Series Bedienungsanleitung Seite 31
- Seite / 110
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
2-11
2
Initial Setup
2-4 Charging the BL-N90
The communication unit is used to charge the BL-N90.
z Charging
Procedure
1 Connect the communication unit to the computer using the appropriate connection method
and make sure both sides are powered on.
For details on connection methods, see "Connecting the Communication Unit" on page 2-5.
2 Set the scanner into the communication unit securely, to ensure that the charging terminals
stay in place.
As the unit begins to charge, the yellow LED on the scanner begins to flash .
Charging is complete once the yellow light stops flashing .
A full charge takes approximately 4 hours.
Note
The barcode reader is shipped with zero charge. Please charge the device before use.
The barcode reader may be used to scan ( page 2-13) after a charge of just 20
minutes.
Note
•
Please periodically clean the charging terminals on the scanner and the
communication unit ( "Maintenance" on page 8).
Dirt in the terminals may interfere with charging.
If too much dirt covers the charging terminals, an alarm may sound.
• The scanner can be configured to sound an alarm when it is unable to charge
properly, such as when the charging terminals are misaligned ( "Charge Error
Prevention" on page 3-13).
• The BL-N90 Series cannot be charged in sleep mode ( page 3-14).
To computer
- BL-N90 Series 1
- Introduction 2
- Laser Safety Precautions 3
- Handling the BL-N90 5
- Wireless Communication 6
- ■ Europe 7
- ■ North America 8
- Precautions on UL and CSA 9
- Maintenance 10
- Table of Contents 11
- Chapter 4 Program 12
- Overview 15
- Checking the Package Contents 16
- BL-N9R BL-N9V 17
- BL-N9UB 17
- Specialized stand OP-82191 18
- 1-2 Part Names 19
- Operation Check LED 20
- Initial Setup 21
- 2-1 Initial Setup 22
- Included parts 23
- BL-N9UB BL-N9V/N9R 24
- 1 Turn on the computer 25
- Installing the USB driver 26
- 1 Turn off the computer 27
- 4 Turn on your computer 28
- 1 Turn on your computer 29
- Conversion connector 30
- (D-sub 9-pin) 30
- 2-4 Charging the BL-N90 31
- Battery low alarm 32
- Continuous use capacity 32
- Charging time 32
- 2-5 Establishing a Connection 33
- Scanning a barcode 34
- Swapping out the BL-N90 34
- Initializing the BL-N90 35
- Readable range 36
- Read distance: 100 mm 36
- Trigger switch 36
- Operation check LED 36
- Precautions for reading 37
- X Incorrect Scan 37
- X Incorrect Scan 37
- Checking the Connected Pair 38
- Obstacle 39
- Descriptions of Key 41
- Functions 41
- 3-1 Reading 42
- Rereading prevention 43
- Limit read digits 43
- Buzzer tone selection 43
- Number of 44
- BL-N90 status 44
- Selecting the Reading Mode 45
- Detection 46
- Descriptions of Key Functions 48
- 3-3 Sending the Reading Data 49
- Inter-character Delay 50
- Localized settings 51
- No protocol 51
- 3-5 Charge Error Prevention 53
- 3-6 Sleep Mode 54
- Configuring the Program 56
- Start/End Program 57
- Initialization 57
- Settings for the Barcode Type 58
- EAN/UPC Detailed Settings 60
- Read only EAN add-on code 62
- GS1-128 62
- Send ]c1 symbol identifier 62
- Group separator settings 62
- Check digit inspection 63
- Send check digit 63
- Send application identifier 65
- Send symbol identifier 65
- 4-4 Setting the Reading Mode 67
- Auto-scan detection distance 68
- 4-5 Buzzer Settings 69
- 4-6 Decode Settings 70
- <375 ms> 500 ms 71
- Limit all settings 72
- Limit individual settings 72
- Block 1 settings 73
- Block 2 settings 73
- Block 3 settings 74
- Block 4 settings 74
- Block 5 settings 74
- Block 6 settings 74
- Block 7 settings 74
- Data Format 75
- <TAB prohibited> 76
- <ETX prohibited> 76
- <1 ms> 10 ms 76
- Keyboard/USB Settings 77
- RS-232C Settings 77
- Stop bit length 78
- Parity check 78
- Communication protocol 78
- 4-10 Other Settings 79
- 4-11 Decimal Program Code 80
- 4-12 Code Type List 81
- A-1 Specifications 84
- Communication unit 85
- A-2 Dimensions 86
- When using the pedestal 87
- When not using the pedestal 87
- Mounting 88
- Fix with double-sided tape 89
- Procedure 90
- A-4 Dedicated Stand 91
- Pedestal 93
- M3 screw 94
- Stand fixture 96
- Stand base 96
- Logo plate 96
- Flathead screw driver 96
- 7 Replace the logo plate 97
- A-5 Troubleshooting 98
- Problem Possible cause Remedy 99
- A-6 ASCII Code Table 100
- Barcode Settings 101
- Setting item Setting content 102
- Factory 102
- Operation Settings 104
- Communication Data Format 106
- Other Settings 107
- Connection Interface 107
- Appendices 108
- WARRANTIES AND DISCLAIMERS 109
Verwandte Produkte und Handbücher für Sensoren Keyence BL-N90 Series
Sensoren Keyence N-48/42 Bedienungsanleitung
(20 Seiten)
(20 Seiten)
Sensoren Keyence DV-90 Bedienungsanleitung
(262 Seiten)
(262 Seiten)
Sensoren Keyence N-400 Bedienungsanleitung
(150 Seiten)
(150 Seiten)
Sensoren Keyence N-410 Bedienungsanleitung
(160 Seiten)
(160 Seiten)
Sensoren Keyence KV Series Bedienungsanleitung
(26 Seiten)
(26 Seiten)
Sensoren Keyence KV Series Bedienungsanleitung
(240 Seiten)
(240 Seiten)
Sensoren Keyence KV-D20 Bedienungsanleitung
(72 Seiten)
(72 Seiten)
Sensoren Keyence MS-F07 Bedienungsanleitung
(2 Seiten)
(2 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 2.546 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern