Keyence LT-9001 Series Bedienungsanleitung Seite 135
- Seite / 176
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
8
Chapter
RS-232C
E LT-9001-IM
8-5
This section describes the details of the incoming commands and the response commands that are sent after
the incoming commands is properly processed.
Refer to “Outline of Command Format” (page 8-3) for error response command. Refer to “Timing Chart”
(page 8-16) for response delay time of the response command.
Measured value output
You can output the measurement result.
Two types of measured value output are available.
• Measured value output Outputs a measured value.
• Measured value reoutput Reoutputs a measured value that has been previously output.
Measured value output
Example: The measured value is output in the format as shown below when the OUT number is 0 and the output
content is 1.
Measured value reoutput
Command Details
- LT-9001 Series 1
- Introduction 2
- Safety Precautions 3
- Measurement target 5
- Scan straightness 5
- Handling 5
- Effect of atmospheric motions 5
- Precaution on CE Marking 6
- Organization of this Manual 7
- Table of Contents 8
- Chapter 8 RS-232C 10
- Chapter 9 Specifications 10
- Appendices 10
- Outline of the LT-9001 11
- System Configuration 12
- Checking the Package Contents 13
- Controller 14
- Measuring Unit 15
- Remote Control Console 16
- Mounting and Connecting Parts 17
- Connection 18
- Outline of Basic 19
- Operations 19
- Displacement Mode 20
- Profile Mode 20
- Program mode screen 21
- Run mode screen 21
- Run Mode 22
- Program Mode 23
- Program Function 26
- Flow of Measurement 27
- Selecting an Item 29
- Entering a Value 29
- Operational Flow 30
- Using the Displacement Mode 31
- Measuring the Displacement 33
- Using the Profile Mode 34
- Setting the Area 36
- Measuring Height Differences 37
- Measuring 38
- Resetting the Device to the 40
- Factory Settings 40
- Scan center 41
- 1st point/measured value 42
- Offset – 999999 + 999999 0 43
- Scan Width 44
- Outline of Displacement 47
- Display Screens 48
- Measurement Screen 49
- Light Intensity Screen 50
- Pause Screen 55
- SELECT SURFACE 58
- OUT Settings 60
- Scan width 61
- Basic Settings 62
- DARK ALARM 63
- Outline of Profile Mode 67
- Types of Screens 68
- Program mode 68
- Run mode 68
- Display of Profile Waveform 72
- Setting the position 73
- Slant correction 77
- WIDTH/INTERVAL 80
- SMOOTH (Smoothing) 83
- PROF OUT (Profile Output) 85
- Outline of Common Operations 87
- X : 2500 μm 88
- Y : 2000 μm 88
- Hold Function 89
- Auto-zero Function 90
- Keylock Function 91
- Program Change 92
- (Output) 94
- HOLD MODE (Measurement mode) 95
- Upper limit of tolerance 96
- Lower limit of tolerance 96
- Measured value 96
- Judgment 97
- Judgment standby status 97
- OUTPUT Settings 100
- ANALOG output 101
- CALIB (Calibration) 102
- E LT-9001-IM 103
- OPTIONAL Settings 104
- DISPLAY UNIT 105
- GAIN (Sensitivity) 106
- Setting up the Basic 107
- Settings for the Overall Unit 107
- List of Default Values 108
- Environment Setting Items 108
- Beep sound ( page 6-7) 109
- Coefficient ( page 6-7) 109
- RS-232C Interface 111
- Items that can be set 112
- Coefficient 113
- Interface Language 113
- Beep Sound 113
- Controlling and Outputting 115
- Terminal number 116
- Terminal 116
- Control I/O 117
- Functions of the I/O Signals 119
- VIDEO Output 119
- Auto-zero input 120
- Program No. change input 120
- Binary output 121
- Laser remote input 121
- Electrical Specifications 122
- Timing Chart 123
- Timing Details (LT-9010 (M)) 127
- Timing Details (LT-9030 (M)) 128
- Connecting to External 131
- Devices via RS-232C 131
- Specifications 132
- Outline of Command Format 133
- Command Details 135
- Profile waveform data output 136
- Timing ON/OFF 136
- Auto-zero ON/OFF 137
- Program No. change 137
- Keylock ON/OFF 137
- S D , O A , x i 138
- Select surface setting 140
- Change HOLD mode setting 140
- Offset setting 140
- Analog scaling setting 141
- Calibration setting 141
- Area setting 141
- Area range setting 141
- Scan width/interval setting 142
- Scan center position setting 142
- FINE mode 142
- Dark-out setting 142
- Dark-out range setting 143
- Mask setting 143
- Mask range setting 143
- Auto slant correction setting 144
- Gain setting 144
- S R , O F , x 145
- ASCII Code Table (Reference) 146
- Synchronization 147
- Output format 148
- Specifications of the 149
- Status Table 152
- Display Update Cycle 154
- Response Delay Time 154
- Outside Dimensions 155
- Troubleshooting 158
- Error Messages 160
- Optional Product List 161
- Parameter Memo 162
- 0.00 0.00 163
- Profile mode 164
- Revision history 174
- WARRANTIES AND DISCLAIMERS 175
Verwandte Produkte und Handbücher für Sensoren Keyence LT-9001 Series
Sensoren Keyence CA-MP81 Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Sensoren Keyence LS-7000 Bedienungsanleitung
(192 Seiten)
(192 Seiten)
Sensoren Keyence LS-7600 Bedienungsanleitung
(220 Seiten)
(220 Seiten)
Sensoren Keyence LS-5000 Bedienungsanleitung
(132 Seiten)
(132 Seiten)
Sensoren Keyence GP-M Series Bedienungsanleitung
(28 Seiten)
(28 Seiten)
Sensoren Keyence AP-40P Bedienungsanleitung
(5 Seiten)
(5 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.063 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern