Keyence LK-G Series Bedienungsanleitung Seite 102
- Seite / 198
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
3-44
3
LK-G-M-NO3-E
3 Function Settings
Accumulating the Measurement Value in the Memory (Data Storage Function)
Up to 131072 measurement values of OUT1 and OUT2 (65536 values for each OUT1 and 2)
can be stored in the internal memory for every accumulation rate. The accumulated data can
be read by using the "RS-232C interface" or "LK-Navigator".
The setting contents of the function No. and the sub-function are as follows.
• The data to be accumulated is the measurement value of OUT1 or of OUT2 after data
processing such as the one in the measurement mode. ( page 3-2)
• The accumulating operation stops when the number of accumulated data exceeds the
specified number.
• The accumulation time can be calculated by "sampling rate x accumulation rate x number of data".
• The data is accumulated at the sampling rate even when the refresh rate is longer than
the sampling rate, which is set in the setting of the average number of times. In such a
case, the same measurement value continues to be accumulated until the
measurement value is updated.
• The accumulation continues without clearing the accumulated data even if [Auto-zero]
or [RESET] is performed.
• When the starting and finishing operation are repeated, the new data is accumulated
after the old data.
■ Starting/finishing the accumulation and clearing the data
Function No. Selection of the
accumulated data
f-d0 off
Does not accumulate data.
f-d1 out1
Accumulates the data of
OUT 1
f-d2 out2
Accumulates the data of
OUT 2
f-d3 out1.2
Accumulated the data of
both OUT1 and 2
Conditions for starting
the accumulation
• Start command from the RS-232 interface.
• Operation from the setup support software "LK-Navigator".
Conditions for finishing
the accumulation
• Stop command from the RS-232 interface
• Operation from the setup support software "LK-Navigator".
Conditions for clearing
the accumulated data
Following operations while stopping the accumulation
• When moving to the measurement mode from the setting mode or communication mode
• When initialization command is sent from the RS-232 interface
• Initializing operation from the setup support software "LK-Navigator"
• When the power is turned off
• When the program No. is changed
Reference
Sub-function Accumulation rate selection
f-F0 1
x 1 (Sampling cycle)
f-F1 2
x 2
f-F2 5
x 5
f-F3 10
x 10
f-F4 20
x 20
f-F5 50
x 50
f-F6 100
x 100
f-F7 200
x 200
f-F8 500
x 500
f-F9 000
x 1000
- LK-G Series 1
- Safety Precautions 3
- Precautions on CE Marking 5
- Precautions for Wiring 6
- LK-G-M-NO0-E 10
- ■ Warning labels 12
- ■ Label contents 12
- ■ Label attachment locations 14
- Organization of this Manual 15
- Table of Contents 17
- ....................3-32 18
- Before Use1 21
- System Configuration 22
- Checking the Package Contents 23
- LK-G-M-NO1-E 24
- LK-GD500: 1 : 1 24
- LK-GC2/GC5/GC10/GC20/GC30 25
- Controller 26
- Operation keys 27
- Terminal panel 27
- Installing the Head 29
- Reference 30
- LK-G35 LK-G35 36
- Installing the Controller 37
- Switching Modes 44
- Setting Mode 45
- Default Settings 46
- LK-G-M-NO2-E 47
- Hysteresis 51
- HI GO LO TIM 54
- Switching Program Nos 55
- Function Settings3 59
- Setting the Head 61
- Translucent object 62
- Transparent object 62
- Transparent object 2 62
- Multi-reflective object 62
- Mounting mode 62
- Setting ABLE 63
- A-1" with the 64
- Setting the Mounting Mode 70
- -99.9999 to +99.9999 0.0000 73
- Transparent object A/B 74
- Minimum display unit 75
- Calculating Between the Heads 76
- ■ Averaging function 80
- [-0 AvG 80
- [-1 LPF 80
- [-2 kPF 80
- Sample-and 83
- Measuring with Offset 90
- Scaling the Analog Output 92
- " with the 93
- Setting the Common Function 95
- LK-G-M-NO3-E 100
- (Environment Settings) 104
- Timing LED 112
- Input/Output Terminals4 113
- Input/Output Terminals 114
- LK-G-M-NO4-E 115
- 6-pin I/O terminal block 116
- Expansion Connector 117
- NPN type PNP type 120
- ■ Non-voltage input 122
- ■ NPN open-collector output 122
- Max. input voltage rating 123
- Short-circuit current (Typ.) 123
- Output impedance 124
- Timing Chart 125
- Sample hold (trigger 2) 127
- Binary output 128
- LASER REMOTE/LASER OFF 129
- Average 130
- RS-232C5 131
- Specifications 132
- LK-G-M-NO5-E 133
- Item Setting value Remarks 134
- Parity check None/Even/Odd 134
- Outline of the command format 135
- 2 3 4 . 5 6 136
- F F F F F F 136
- Command list 137
- Incoming command 138
- Operation Response command 138
- Command details 139
- ● Auto-zero ON 140
- ● Auto-zero OFF 140
- ● Program No. change 141
- ● Program No. check 141
- ● Statistical result output 141
- ● Clearing statistics 141
- Analog output 143
- 0 1 0 000 148
- TIMING input 153
- LK-G-M-NO6-E 155
- Specifications of the Head 158
- ■ LK-G35/LK-G30 159
- 3a (CDRH) 159
- ■ LK-G37/LK-G32 160
- 2 (CDRH) 160
- ■ LK-G85/LK-G80 161
- ■ LK-G87/LK-G82 162
- ■ LK-G155/LK-G150 163
- ■ LK-G157/LK-G152 164
- ■ LK-G405/LK-G400 165
- ■ LK-G407/LK-G402 166
- ■ LK-G505/LK-G500 167
- ■ LK-G507/LK-G502 168
- Status Table 169
- Unit (mm) 171
- LK-G3001/ 172
- LK-GD500 Panel cutout 172
- Specular reflection setup 173
- Characteristics 179
- Appendices7 185
- Troubleshooting 186
- LK-G-M-NOA-E 187
- Error Messages 189
- List of Optional Products 190
- Revision history 196
- Introduction 197
Verwandte Produkte und Handbücher für Sensoren Keyence LK-G Series
Sensoren Keyence LK-H1W Bedienungsanleitung
(84 Seiten)
(84 Seiten)
Sensoren Keyence LK-3100 Bedienungsanleitung
(24 Seiten)
(24 Seiten)
Sensoren Keyence CB-EP100 Bedienungsanleitung
(146 Seiten)
(146 Seiten)
Sensoren Keyence LJ-H1W Bedienungsanleitung
(104 Seiten)
(104 Seiten)
Sensoren Keyence LT-9001 Series Bedienungsanleitung
(176 Seiten)
(176 Seiten)
Sensoren Keyence CA-MP81 Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Sensoren Keyence LS-7000 Bedienungsanleitung
(192 Seiten)
(192 Seiten)
Sensoren Keyence LS-7600 Bedienungsanleitung
(220 Seiten)
(220 Seiten)
Sensoren Keyence LS-5000 Bedienungsanleitung
(132 Seiten)
(132 Seiten)
Sensoren Keyence GP-M Series Bedienungsanleitung
(28 Seiten)
(28 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.139 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern