Keyence LK-G Series Bedienungsanleitung Seite 43
- Seite / 198
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
1-23
1
LK-G-M-NO1-E
1 Before Use
■ Connecting the display panel
In the case of the separate type controller, the display panel cable is used for connecting the
controller to the display panel.
The LK-G series can be operated without the display panel. In addition, the operation from
a PC is possible by using the "LK-Navigator" software.
■ Connecting the power
Connect the 24V DC power to the terminals 1 and 2 of the 12-pin terminal block.
KEYENCE CA-U3 is recommended for the 24V DC power supply.
■ Connecting the terminal block
The steps to connect the wires to the terminal block are as follows:
1
Remove the terminal block from the controller.
Loosen the two screws with a screwdriver and pull it out.
2
Loosen the screws on the terminal with a screwdriver, and insert the lead wires
into the terminal block.
Approximately 6.5mm of the insulation should be striped from both wires.
3
Tighten the lead wires with the screwdriver.
After tightening them, pull the lead wires lightly to confirm that they are securely
fixed.
4
Install the terminal block to the controller.
Reference
Reference
- LK-G Series 1
- Safety Precautions 3
- Precautions on CE Marking 5
- Precautions for Wiring 6
- LK-G-M-NO0-E 10
- ■ Warning labels 12
- ■ Label contents 12
- ■ Label attachment locations 14
- Organization of this Manual 15
- Table of Contents 17
- ....................3-32 18
- Before Use1 21
- System Configuration 22
- Checking the Package Contents 23
- LK-G-M-NO1-E 24
- LK-GD500: 1 : 1 24
- LK-GC2/GC5/GC10/GC20/GC30 25
- Controller 26
- Operation keys 27
- Terminal panel 27
- Installing the Head 29
- Reference 30
- LK-G35 LK-G35 36
- Installing the Controller 37
- Switching Modes 44
- Setting Mode 45
- Default Settings 46
- LK-G-M-NO2-E 47
- Hysteresis 51
- HI GO LO TIM 54
- Switching Program Nos 55
- Function Settings3 59
- Setting the Head 61
- Translucent object 62
- Transparent object 62
- Transparent object 2 62
- Multi-reflective object 62
- Mounting mode 62
- Setting ABLE 63
- A-1" with the 64
- Setting the Mounting Mode 70
- -99.9999 to +99.9999 0.0000 73
- Transparent object A/B 74
- Minimum display unit 75
- Calculating Between the Heads 76
- ■ Averaging function 80
- [-0 AvG 80
- [-1 LPF 80
- [-2 kPF 80
- Sample-and 83
- Measuring with Offset 90
- Scaling the Analog Output 92
- " with the 93
- Setting the Common Function 95
- LK-G-M-NO3-E 100
- (Environment Settings) 104
- Timing LED 112
- Input/Output Terminals4 113
- Input/Output Terminals 114
- LK-G-M-NO4-E 115
- 6-pin I/O terminal block 116
- Expansion Connector 117
- NPN type PNP type 120
- ■ Non-voltage input 122
- ■ NPN open-collector output 122
- Max. input voltage rating 123
- Short-circuit current (Typ.) 123
- Output impedance 124
- Timing Chart 125
- Sample hold (trigger 2) 127
- Binary output 128
- LASER REMOTE/LASER OFF 129
- Average 130
- RS-232C5 131
- Specifications 132
- LK-G-M-NO5-E 133
- Item Setting value Remarks 134
- Parity check None/Even/Odd 134
- Outline of the command format 135
- 2 3 4 . 5 6 136
- F F F F F F 136
- Command list 137
- Incoming command 138
- Operation Response command 138
- Command details 139
- ● Auto-zero ON 140
- ● Auto-zero OFF 140
- ● Program No. change 141
- ● Program No. check 141
- ● Statistical result output 141
- ● Clearing statistics 141
- Analog output 143
- 0 1 0 000 148
- TIMING input 153
- LK-G-M-NO6-E 155
- Specifications of the Head 158
- ■ LK-G35/LK-G30 159
- 3a (CDRH) 159
- ■ LK-G37/LK-G32 160
- 2 (CDRH) 160
- ■ LK-G85/LK-G80 161
- ■ LK-G87/LK-G82 162
- ■ LK-G155/LK-G150 163
- ■ LK-G157/LK-G152 164
- ■ LK-G405/LK-G400 165
- ■ LK-G407/LK-G402 166
- ■ LK-G505/LK-G500 167
- ■ LK-G507/LK-G502 168
- Status Table 169
- Unit (mm) 171
- LK-G3001/ 172
- LK-GD500 Panel cutout 172
- Specular reflection setup 173
- Characteristics 179
- Appendices7 185
- Troubleshooting 186
- LK-G-M-NOA-E 187
- Error Messages 189
- List of Optional Products 190
- Revision history 196
- Introduction 197
Verwandte Produkte und Handbücher für Sensoren Keyence LK-G Series
Sensoren Keyence LK-H1W Bedienungsanleitung
(84 Seiten)
(84 Seiten)
Sensoren Keyence LK-3100 Bedienungsanleitung
(24 Seiten)
(24 Seiten)
Sensoren Keyence CB-EP100 Bedienungsanleitung
(146 Seiten)
(146 Seiten)
Sensoren Keyence LJ-H1W Bedienungsanleitung
(104 Seiten)
(104 Seiten)
Sensoren Keyence LT-9001 Series Bedienungsanleitung
(176 Seiten)
(176 Seiten)
Sensoren Keyence CA-MP81 Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Sensoren Keyence LS-7000 Bedienungsanleitung
(192 Seiten)
(192 Seiten)
Sensoren Keyence LS-7600 Bedienungsanleitung
(220 Seiten)
(220 Seiten)
Sensoren Keyence LS-5000 Bedienungsanleitung
(132 Seiten)
(132 Seiten)
Sensoren Keyence GP-M Series Bedienungsanleitung
(28 Seiten)
(28 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern