Keyence LS-5000 Bedienungsanleitung Seite 124
- Seite / 132
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Appendices
118
Appendices
Appendix C Troubleshooting Guide
If a condition occurs that could be due to equipment failure or malfunction, follow
the inspection procedures given below.
If the LS-5000 series does not operate normally after this inspection, contact the
nearest KEYENCE dealer or sales office.
ProblemItem
Inspection
Action
Ref. page
Measured
value
display
p.8, 13
• Measured value is
not displayed.
• Nothing is dis-
played.
• Check power switch.
• Turn power switch ON.
• Check connection with power
supply.
• Connect AC power cable.
(LS-5501)
“- - - - -” is displayed. • Check if target is correctly
placed in measurement area.
• Check if scanning area is
entirely covered.
• Check if AREA is correctly
selected.
• Check if scanning head is
connected.
• Check laser emitting/receiving
windows for dust or dirt.
• Check if laser ON alarm indica-
tor is lit.
• Check if power switch has just
been turned ON.
• Check if the measurement
mode has just been changed.
• Check number of averaging
measurements.
• Check condensation.
• Place target in measurement
area correctly.
• Select AREA correctly.
• Turn power OFF. Connect
scanning head, and turn power
ON.
• Remove dust or dirt from laser
emitting/receiving window.
• Short-circuit LASER REMOTE
terminals.
• Wait for approx. 10 seconds
after turning power ON.
• Wait for approx. 3 seconds
after changing the measure-
ment mode.
• Depending on No. of averaging
measurements, approx. 2.6 or
less seconds is required to
display measured value after
target is placed in measuring
area.
• Change measurement environ-
ment.
p.115
p.39
p.13
p.60
p.4
p.13
p.44
Measured value
fluctuates.
• Check if target is correctly
placed in measurement area.
• Check if reference edge is set
in measurement area.
• Check laser emitting/receiving
windows for dust or dirt.
• Check target for dust or dirt.
• Check for large variations in
ambient temperature.
• Place target in measurement
area correctly.
• Set reference edge (when
T.EDGE/B.EDGE mode is
used).
• Remove dust or dirt.
• Keep ambient temperature
constant.
p.115
p.60
- LS-5000 Series 1
- Safety Precautions 2
- Warranty 3
- Contents 4
- Chapter 6 Normal mode 5
- Chapter 7 Pitch Mode 5
- Chapter 8 RS-232C I/O 6
- Chapter 9 Expansion I/O Board 6
- WARRANTIES AND DISLAIMERS 125 6
- Chapter 1 7
- 1.1 Classification 8
- 1.2 Warning Labels 8
- 1.3 Label Location 9
- 1.4 Safety Consideration 9
- Laser emission remote 10
- LS-5121T 11
- 1.6 Preparation for Operation 12
- Chapter 2 13
- 2.1.1 System Configuration 14
- Frame cover Frame cover 15
- Transmitter Receiver 16
- LS-C3 (3 m) 16
- To ROM board 16
- Frame cover Frame cover 17
- 5 • 0 0 0 0 – 18
- 2.3 Part Names 19
- LS-5041/5121 (Scanning head) 20
- Chapter 3 21
- 3.1 Quick Start Reference 22
- Chapter 4 23
- Chapter 4 Installation 24
- DIN rail 25
- Chapter 5 27
- 5.1 Area/Segment/Edge 28
- 5.2 Normal Mode 28
- 5.2.1 DIA Mode 29
- 5.2.3 SEG (m,n) Mode 29
- 5.3 Pitch Mode 30
- Chapter 6 31
- 6.1 Normal Mode Screens 32
- 6.2 Initial Screen 33
- DIAHEAD2 34
- ( 2, 3) 34
- 6.4 Setting Functions 35
- 1 [HOLD] Hold Function 36
- 2 [ZERO] Auto-zero Function 37
- Chapter 6 Normal Mode 38
- OUT1 • • • OUT4 41
- AREA1CALIB • • • AREA4 42
- PROGRAM 44
- HEAD1 HEAD2 HEAD3 HEAD4 45
- LASER ON AREA SETUP 47
- OUTPUT MODEOUT1LASER ON P. 1 49
- SELF-TIMING 49
- INTERVAL (ms) 49
- OUTPUT OUT1 • • • OUT4 50
- Measures 52
- A Digit Suppression Function 60
- B Offset Function 61
- C Analog Output Function 63
- LASER ON OUTPUT MODE 64
- D I/O Slot Setup 65
- E Inspection 66
- Optical axis 68
- H Display Unit 71
- I Area Check Function 72
- The current settings 73
- OK CANCEL 73
- Mode changed to Pitch 74
- Chapter 7 75
- 7.1 Pitch Mode Screens 76
- 7.2 Initial Screen 77
- 7.3 Setting Measurement 78
- 7.4 Setting Functions 79
- Chapter 7 Pitch Mode 80
- The number 83
- Missing pin 84
- HEAD1 Err 84
- Max - - - - - - 84
- Min - - - - - - 84
- HEAD1 • • • HEAD4 85
- Mode Description 87
- MODE CHANGE 91
- Chapter 8 93
- Chapter 8 RS-232C I/O 94
- 8.2 Remote Control Function 96
- Control Command 1 99
- Function Command received 100
- Description 100
- Selection 50H##0DH 100
- Reading Preset Data (Batch) 101
- Writing Preset Data (Batch) 102
- 8.3 Command List 103
- Sample Program (BASIC) 104
- Chapter 9 105
- 12 11 10 987654321 106
- 9.1.2 I/O Terminal Operations 107
- 9.1.3 Specifications 108
- Chapter 10 109
- 10.1 Display System Setup 110
- OPTION SETUP 111
- 10.1.3 Adjusting Contrast 112
- SELF-CHECK 112
- LS SYSTEM SETUP 112
- TO RUN MODE 112
- 10.1.6 Numeric Keys 115
- SYSTEM MODE 116
- Align the corners of 117
- ■ LS-5501 118
- ■ LS-5001 118
- Appendices 119
- Appendix B Initial Settings 122
- PITCH Mode 123
- ProblemItem 124
- Inspection 124
- Ref. page 124
- WARRANTIES AND DISCLAIMERS 131
Verwandte Produkte und Handbücher für Sensoren Keyence LS-5000
Sensoren Keyence GP-M Series Bedienungsanleitung
(28 Seiten)
(28 Seiten)
Sensoren Keyence AP-40P Bedienungsanleitung
(5 Seiten)
(5 Seiten)
Sensoren Keyence DL-CL1 Bedienungsanleitung
(78 Seiten)
(78 Seiten)
Sensoren Keyence SK-H Series Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Sensoren Keyence IV Series Bedienungsanleitung
(10 Seiten)
(10 Seiten)
Sensoren Keyence IV Series Bedienungsanleitung
(110 Seiten)
(110 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.185 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern