Keyence LS-5000 Bedienungsanleitung Seite 29
- Seite / 132
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 5 Outline of Measurements
23
5
5.2.1 DIA Mode
Example: Outer diameter measurement using a rod or transparent object
The width between the lower edge of the first light segment and the top edge of the
last light segment is measured.
• When one target is measured
• When several targets are measured
5.2.2 T.EDGE (TOP EDGE) Mode / B.EDGE (BOTTOM EDGE) Mode
Example: Measurement of a gap between rollers
T.EDGE: Measures the width of the first light segment.
B.EDGE: Measures the width of the last light segment.
5.2.3 SEG (m,n) Mode
Example: Inner diameter measurement using a bearing
When two edges are specified, the width between these edges is measured.
* (m,n) indicates any number between 0 and 254. “m” should be smaller than “n”.
Note: DIA mode
Since DIA mode is basically intended for outer diameter measurement of a rod,
transparent tube or other round surface, the measurement error due to the round
surface is calibrated.
To perform outer diameter measurement of a round target, select DIA mode.
Photodiode for synchronization
Laser
scanning
direction
Target
Measured
width
Transmitter Receiver
Photodiode for synchronization
Target
Measured
width
Transmitter Receiver
Photodiode for synchronization
Target
The T.EDGE mode
measures this width.
The B.EDGE mode
measures this width.
Transmitter Receiver
Photodiode for synchronization
Target
Both the T.EDGE and B.EDGE
modes measure this width.
Transmitter Receiver
Photodiode for synchronization
Target
This width is measured
when SEG(3,4) is set.
Transmitter Receiver
0
1
2
3
4
5
6
- LS-5000 Series 1
- Safety Precautions 2
- Warranty 3
- Contents 4
- Chapter 6 Normal mode 5
- Chapter 7 Pitch Mode 5
- Chapter 8 RS-232C I/O 6
- Chapter 9 Expansion I/O Board 6
- WARRANTIES AND DISLAIMERS 125 6
- Chapter 1 7
- 1.1 Classification 8
- 1.2 Warning Labels 8
- 1.3 Label Location 9
- 1.4 Safety Consideration 9
- Laser emission remote 10
- LS-5121T 11
- 1.6 Preparation for Operation 12
- Chapter 2 13
- 2.1.1 System Configuration 14
- Frame cover Frame cover 15
- Transmitter Receiver 16
- LS-C3 (3 m) 16
- To ROM board 16
- Frame cover Frame cover 17
- 5 • 0 0 0 0 – 18
- 2.3 Part Names 19
- LS-5041/5121 (Scanning head) 20
- Chapter 3 21
- 3.1 Quick Start Reference 22
- Chapter 4 23
- Chapter 4 Installation 24
- DIN rail 25
- Chapter 5 27
- 5.1 Area/Segment/Edge 28
- 5.2 Normal Mode 28
- 5.2.1 DIA Mode 29
- 5.2.3 SEG (m,n) Mode 29
- 5.3 Pitch Mode 30
- Chapter 6 31
- 6.1 Normal Mode Screens 32
- 6.2 Initial Screen 33
- DIAHEAD2 34
- ( 2, 3) 34
- 6.4 Setting Functions 35
- 1 [HOLD] Hold Function 36
- 2 [ZERO] Auto-zero Function 37
- Chapter 6 Normal Mode 38
- OUT1 • • • OUT4 41
- AREA1CALIB • • • AREA4 42
- PROGRAM 44
- HEAD1 HEAD2 HEAD3 HEAD4 45
- LASER ON AREA SETUP 47
- OUTPUT MODEOUT1LASER ON P. 1 49
- SELF-TIMING 49
- INTERVAL (ms) 49
- OUTPUT OUT1 • • • OUT4 50
- Measures 52
- A Digit Suppression Function 60
- B Offset Function 61
- C Analog Output Function 63
- LASER ON OUTPUT MODE 64
- D I/O Slot Setup 65
- E Inspection 66
- Optical axis 68
- H Display Unit 71
- I Area Check Function 72
- The current settings 73
- OK CANCEL 73
- Mode changed to Pitch 74
- Chapter 7 75
- 7.1 Pitch Mode Screens 76
- 7.2 Initial Screen 77
- 7.3 Setting Measurement 78
- 7.4 Setting Functions 79
- Chapter 7 Pitch Mode 80
- The number 83
- Missing pin 84
- HEAD1 Err 84
- Max - - - - - - 84
- Min - - - - - - 84
- HEAD1 • • • HEAD4 85
- Mode Description 87
- MODE CHANGE 91
- Chapter 8 93
- Chapter 8 RS-232C I/O 94
- 8.2 Remote Control Function 96
- Control Command 1 99
- Function Command received 100
- Description 100
- Selection 50H##0DH 100
- Reading Preset Data (Batch) 101
- Writing Preset Data (Batch) 102
- 8.3 Command List 103
- Sample Program (BASIC) 104
- Chapter 9 105
- 12 11 10 987654321 106
- 9.1.2 I/O Terminal Operations 107
- 9.1.3 Specifications 108
- Chapter 10 109
- 10.1 Display System Setup 110
- OPTION SETUP 111
- 10.1.3 Adjusting Contrast 112
- SELF-CHECK 112
- LS SYSTEM SETUP 112
- TO RUN MODE 112
- 10.1.6 Numeric Keys 115
- SYSTEM MODE 116
- Align the corners of 117
- ■ LS-5501 118
- ■ LS-5001 118
- Appendices 119
- Appendix B Initial Settings 122
- PITCH Mode 123
- ProblemItem 124
- Inspection 124
- Ref. page 124
- WARRANTIES AND DISCLAIMERS 131
Verwandte Produkte und Handbücher für Sensoren Keyence LS-5000
Sensoren Keyence GP-M Series Bedienungsanleitung
(28 Seiten)
(28 Seiten)
Sensoren Keyence AP-40P Bedienungsanleitung
(5 Seiten)
(5 Seiten)
Sensoren Keyence DL-CL1 Bedienungsanleitung
(78 Seiten)
(78 Seiten)
Sensoren Keyence SK-H Series Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Sensoren Keyence IV Series Bedienungsanleitung
(10 Seiten)
(10 Seiten)
Sensoren Keyence IV Series Bedienungsanleitung
(110 Seiten)
(110 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.060 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern